M24512-WMW6T datasheet(7/24 Pages) STMICROELECTRONICS

Part #	M24512-WMW6T

Description	512 Kbit Serial I짰 Bus EEPROM

Download	24 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

7 / 24 page

7/24

M24512

DEVICE OPERATION

The device supports the I2C protocol. This is sum-

marized in Figure 5.. Any device that sends data

on to the bus is defined to be a transmitter, and

any device that reads the data to be a receiver.

The device that controls the data transfer is known

as the bus master, and the other as the slave de-

vice. A data transfer can only be initiated by the

bus master, which will also provide the serial clock

for synchronization. The M24512 device is always

a slave in all communication.

Start Condition

Start is identified by a falling edge of Serial Data

(SDA) while Serial Clock (SCL) is stable in the

High state. A Start condition must precede any

data transfer command. The device continuously

monitors (except during a Write cycle) Serial Data

(SDA) and Serial Clock (SCL) for a Start condition,

and will not respond unless one is given.

Stop Condition

Stop is identified by a rising edge of Serial Data

(SDA) while Serial Clock (SCL) is stable and driv-

en High. A Stop condition terminates communica-

tion between the device and the bus master. A

Read command that is followed by NoAck can be

followed by a Stop condition to force the device

into the Stand-by mode. A Stop condition at the

end of a Write command triggers the internal Write

cycle.

Acknowledge Bit (ACK)

The acknowledge bit is used to indicate a success-

ful byte transfer. The bus transmitter, whether it be

bus master or slave device, releases Serial Data

(SDA) after sending eight bits of data. During the

9th clock pulse period, the receiver pulls Serial

Data (SDA) Low to acknowledge the receipt of the

eight data bits.

Data Input

During data input, the device samples Serial Data

(SDA) on the rising edge of Serial Clock (SCL).

For correct device operation, Serial Data (SDA)

must be stable during the rising edge of Serial

Clock (SCL), and the Serial Data (SDA) signal

must change

only when Serial Clock (SCL) is driv-

en Low.

Memory Addressing

To start communication between the bus master

and the slave device, the bus master must initiate

a Start condition. Following this, the bus master

sends the Device Select Code, shown in Table 3.

(on Serial Data (SDA), most significant bit first).

The Device Select Code consists of a 4-bit Device

Type Identifier, and a 3-bit Chip Enable “Address”

(E2, E1, E0). To address the memory array, the 4-

bit Device Type Identifier is 1010b.

Up to eight memory devices can be connected on

a single I2C bus. Each one is given a unique 3-bit

code on the Chip Enable (E0, E1, E2) inputs.

When the Device Select Code is received, the de-

vice only responds if the Chip Enable Address is

the same as the value on the Chip Enable (E0, E1,

E2) inputs.

The 8th bit is the Read/Write bit (RW). This bit is

set to 1 for Read and 0 for Write operations.

If a match occurs on the Device Select code, the

corresponding device gives an acknowledgment

on Serial Data (SDA) during the 9th bit time. If the

device does not match the Device Select code, it

deselects itself from the bus, and goes into Stand-

by mode.

Table 6. Operating Modes

Note: 1. X =

VIH or VIL.

Mode

RW bit

WC 1

Bytes

Initial Sequence

Current Address Read

1

X

1

START, Device Select, RW = 1

Random Address Read

0X

1

START, Device Select, RW = 0, Address

1

X

reSTART, Device Select, RW = 1

Sequential Read

1

X

≥ 1

Similar to Current or Random Address Read

Byte Write

0

VIL

1

START, Device Select, RW = 0

Page Write

0

VIL

≤ 128

START, Device Select, RW = 0

Similar Part No. - M24512-WMW6T

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M24512-WMW6TG	265Kb / 31P	512 Kbit and 256 Kbit Serial I2C bus EEPROM with three Chip Enable lines
STMicroelectronics	M24512-WMW6TP	265Kb / 31P	512 Kbit and 256 Kbit Serial I2C bus EEPROM with three Chip Enable lines

More results

Similar Description - M24512-WMW6T

Manufacturer	Part #	Datasheet	Description
Microchip Technology	25AA512	670Kb / 36P	512 Kbit SPI Bus Serial EEPROM 2010
	25LC512	502Kb / 30P	512 Kbit SPI Bus Serial EEPROM 10/28/13
	25AA512	620Kb / 32P	512 Kbit SPI Bus Serial EEPROM 2007
	25A512	392Kb / 34P	512 Kbit SPI Bus Serial EEPROM 05/02/11
	25LC512	664Kb / 36P	512 Kbit SPI Bus Serial EEPROM 2010
STMicroelectronics	M95512-RMN6P	1Mb / 50P	512-Kbit serial SPI bus EEPROM
	M24512-W	401Kb / 40P	512-Kbit serial I짼C bus EEPROM
	M24512-125	293Kb / 30P	Automotive 512-Kbit serial IC bus EEPROM
	M24512-W	737Kb / 47P	512-Kbit serial I²C bus EEPROM Rev 31 - October 2020
	M95512-125	293Kb / 38P	Automotive 512-Kbit serial SPI bus EEPROM

More results

M24512-WMW6T Datasheet(PDF) 7 Page - STMicroelectronics

M24512-WMW6T Datasheet(HTML) 7 Page - STMicroelectronics

Similar Part No. - M24512-WMW6T

Similar Description - M24512-WMW6T

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Download

Link URL