Electronic Components Datasheet Search |
|
MAX5924BEUB Datasheet(PDF) 4 Page - Maxim Integrated Products |
|
MAX5924BEUB Datasheet(HTML) 4 Page - Maxim Integrated Products |
4 / 22 page 1V to 13.2V, n-Channel Hot-Swap Controllers Require No Sense Resistor 4 _______________________________________________________________________________________ Typical Operating Characteristics (VCC = 5V, CL = 1µF, CSLEW = 330nF, CGATE = 10nF, RL = 500 Ω, Figure 1, TA = +25°C, unless otherwise noted.) MAX5926 SUPPLY CURRENT vs. SUPPLY VOLTAGE VCC (V) 12 10 8 6 4 0.4 0.8 1.2 1.6 2.0 0 214 VCC = VS ENABLED DISABLED MAX5926 SUPPLY CURRENT vs. TEMPERATURE TEMPERATURE ( °C) -40 -15 10 35 60 85 0 0.4 0.8 1.2 1.6 2.0 2.4 VCC = 13.2V VCC = VS VCC = 5.0V VCC = 3.0V VCC = 2.25V GATE-DRIVE VOLTAGE vs. SUPPLY VOLTAGE VCC (V) 12 10 8 6 4 3 4 5 6 7 2 214 VS = 1V VS = 3V VS = 5V VS = VCC ELECTRICAL CHARACTERISTICS (continued) (VCC, EN (MAX5924/MAX5925), EN1 (MAX5926) = +2.25V to +13.2V; EN2 (MAX5926) = 0V; VS (see Figure 1) = +1.05V to VCC; TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = 5V, RL = 500 Ω from OUT to GND, CL = 1µF, SLEW = open, TA = +25°C, unless otherwise noted.) (Note 1) Note 1: All devices are 100% tested at TA = +25°C and +85°C. All temperature limits at -40°C are guaranteed by design. Note 2: VCC drops 30% below the undervoltage lockout voltage during tDG are ignored. Note 3: RLP is the resistance measured between VCC and SC_DET during the load-probing phase, tLP. Note 4: Tested at +25°C & +85°C. Guaranteed by design at -40°C. Note 5: The circuit-breaker programming current increases linearly from VCC = 2.25V to 5V. See the Circuit-Breaker Current vs. Supply Voltage graph in the Typical Operating Characteristics. Note 6: See the Startup Mode section for more information. Note 7: VGATE is clamped to 17V (typ) above ground. Note 8: dv/dt = 330 x 10-9/CSLEW (V/ms), nMOS device used for measurement was IRF9530N. Slew rate is measured at the load. PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS LOGIC AND TIMING (TC, LATCH (MAX5926), EN2 (MAX5926) Autoretry Delay tRETRY Autoretry mode 0.6 1.6 3.3 s VIH 2.0 Input Voltage VIL 0.4 V Input Bias Current IBIAS Logic high at 13.2V 3 µA Time to Clear a Latched Fault TCLR MAX5924A/ MAX5924B MAX5925A/ MAX5925B MAX5926 in latched mode 200 µS |
Similar Part No. - MAX5924BEUB |
|
Similar Description - MAX5924BEUB |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |