Electronic Components Datasheet Search |
|
UJA1061TW Datasheet(PDF) 9 Page - NXP Semiconductors |
|
UJA1061TW Datasheet(HTML) 9 Page - NXP Semiconductors |
9 / 74 page UJA1061_5 © NXP B.V. 2007 Nov 23. All rights reserved. Product data sheet Rev. 05 — 22 November 2007 9 of 74 NXP Semiconductors UJA1061 Fault-tolerant CAN/LIN fail-safe system basis chip 6.2.1 Start-up mode Start-up mode is the ‘home page’ of the SBC. This mode is entered when battery and ground are connected for the first time. Start-up mode is also entered after any event that results in a system reset. The reset source information is provided by the SBC to support different software initialization cycles that depend on the reset event. It is also possible to enter Start-up mode via a wake-up from Standby mode, Sleep mode or Fail-safe mode. Such a wake-up can originate either from the CAN-bus, the LIN-bus or from the local WAKE pin. On entering Start-up mode a lengthened reset time tRSTNL is observed. This reset time is either user-defined (via the RLC bit in the System Configuration register) or defaults to the value as given in Section 6.13.12. During the reset lengthening time pin RSTN is held LOW by the SBC. When the reset time is completed (pin RSTN is released and goes HIGH) the watchdog timer will wait for initialization. If the watchdog initialization is successful, the selected operating mode (Normal mode or Flash mode) will be entered. Otherwise the Restart mode will be entered. 6.2.2 Restart mode The purpose of the Restart mode is to give the application a second chance to start up, should the first attempt from Start-up mode fail. Entering Restart mode will always set the reset lengthening time tRSTNL to the higher value to guarantee the maximum reset length, regardless of previous events. If start-up from Restart mode is successful (the previous problems do not reoccur and watchdog initialization is successful), then the selected operating mode will be entered. From Restart mode this must be Normal mode. If problems persist or if V1 fails to start up, then Fail-safe mode will be entered. 6.2.3 Fail-safe mode Severe fault situations will cause the SBC to enter Fail-safe mode. Fail-safe mode is also entered if start-up from Restart mode fails. Fail-safe mode offers the lowest possible system power consumption from the SBC and from the external components controlled by the SBC. A wake-up (via the CAN-bus, the LIN-bus or the WAKE pin) is needed to leave Fail-safe mode. This is only possible if the on-chip oscillator is running correctly. The SBC restarts from Fail-safe mode with a defined delay tret, to guarantee a discharged V1 before entering Start-up mode. Regulator V1 will restart and the reset lengthening time tRSTNL is set to the higher value; see Section 6.5.1. 6.2.4 Normal mode Normal mode gives access to all SBC system resources, including CAN, LIN, INH/LIMP and EN. Therefore in Normal mode the SBC watchdog runs in (programmable) Window mode, for strictest software supervision. Whenever the watchdog is not properly served a system reset is performed. Interrupts from SBC to the host microcontroller are also monitored. A system reset is performed if the host microcontroller does not respond within tRSTN(INT). |
Similar Part No. - UJA1061TW |
|
Similar Description - UJA1061TW |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |