CAT.8100V

After applying the pressure load of 5N

for 10 ± 1 seconds horizontally to the

center of capacitor side body which has

no electrode and has been soldered

beforehand on an aluminum substrate,

there shall be found neither exfoliation

nor its sign at the terminal electrode.

4

6.3

10

16

20

25

35

0G

0J

1A

1C

1D

1E

1V

1

105

P

1.5

155

P

S

A

2.2

225

P

3.3

335

P

P

A

A

4.7

475

P

P

6.8

685

P

(Q)

10

106

P

P

15

156

P

P

P

22

226

P

P

33

336

P

47

476

B

68

686

100

107

150

157

220

227

330

337

470

477

(B)

V

• After 1 minute's application of rated voltage, leakage current at 20˚C is not

more than 0.01CV or 0.5 µA, whichever is greater.

• After 1 minute's application of rated voltage, leakage current at 85˚C is not

more than 0.1CV or 5 µA, whichever is greater.

• After 1 minute's application of derated voltage, leakage current at 125˚C is

not more than 0.125CV or 6.3 µA, whichever is greater.

Dipping Flow at 260˚C for 10 seconds, reflow at 260˚C for 10 seconds

+15% Max. (at +125˚C)

+10% Max. (at + 85˚C)

--10% Max. (at --55˚C)

Damp Heat

Temperature Cycles

At 40˚C, 90 ~ 95% R.H., For 500 hours (No voltage applied)

At --55˚C / +125˚C, 30 minutes each, For 5 cycles,

Resistance to

Soldering Heat

After 2000 hours' application of rated voltage at 85˚C, or derated voltage at

125˚C, capacitors meet the characteristic requirements listed below.

After application of surge voltage in series with a 33

seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85˚C,

capacitors meet the characteristics requirements listed below.

Shear Test

Terminal Strength

Keeping a capacitor surface-mounted on a substrate upside

down and supporting the substrate at both of the opposite

bottom points 45mm apart from the center of the capacitor,

the pressure strength is applied with

a specified jig at the center of the

substrate so that the substrate may

bend by 1mm as illustrated. Then,

there shall be found no remarkable

abnormality on the capacitor terminals.

For 10

± 1 seconds

SOLID TANTALUM ELECTROLYTIC CAPACITORS

Chip

Specifications

Type numbering system (Example : 35V 1.5 µF)

Drawing

L

W

H

Solder electrode

electrode

Solder

AB

C

(D)

Resin

Single-side electrodes

(Both electrodes at bottom side only)

Item

Category

Temperature Range

Capacitance Tolerance

Dissipation Factor

(at 120Hz)

Leakage Current

Capacitance Change

by Temperature

Per formance Characteristics

--55 ~ +125˚C (Rated temperature : 85˚C)

± 20%, ± 10% (at 120Hz) (However P.Q.T Case ± 20%)

D dimension only for reference

( ) The series in parentheses are being developed.

Please contact to your local Nichicon sales office when

these series are being designed in your application.

Dimensions

Refer to P.235

R230

45

45

20

∗ As for the surge and derated voltage at 125˚C, refer to page 266 for details.

Standard ratings

(mm)

Cap.

(

Code

Refer to P.235

ESR(100kHz)

Taping code

(Refer to page 267 for details)

Single face electrode

F

1

9

2

5

3

1

4

V

5

1

6

5

7

5

8

M

9

A

10 11

A

12

Q

13

2

14

Case code

Capacitance tolerance

Rated Capacitance Rated voltage

Series

case code

L

2.2 ± 0.3 1.25 ± 0.3 1.0 ± 0.2

0.6 ± 0.3

0.8 ± 0.3

0.8 ± 0.3

W

H

A

B

C

( D )

(0.2)

P

3.2 ± 0.2

1.6 ± 0.2

0.8 ± 0.2

0.8 ± 0.2

1.2 ± 0.2

0.8 ± 0.2

(0.2)

Q

3.2 ± 0.3

1.6 ± 0.3

1.0 ± 0.2

0.8 ± 0.3

1.2 ± 0.3

0.8 ± 0.3

(0.2)

S

1.4 ± 0.2

1.0 ± 0.2

0.8 ± 0.3

0.8 ± 0.2

1.2 ± 0.3

1.2 ± 0.2

0.8 ± 0.3

1.1 ± 0.2

1.7 ± 0.3

2.7 ± 0.2

3.2 ± 0.3

3.5 ± 0.2

(0.2)

(0.2)

A

T

1.8 ± 0.2

0.8 ± 0.3

1.2 ± 0.3

1.1 ± 0.3

2.7 ± 0.3

3.3 ± 0.3

(0.2)

B

Adapted to the RoHS directive (2002/95/EC).