Electronic Components Datasheet Search |
|
F971A225MAA Datasheet(PDF) 1 Page - Nichicon corporation |
|
F971A225MAA Datasheet(HTML) 1 Page - Nichicon corporation |
1 / 2 page CAT.8100V 5N (0.51kg • f) For 10 ± 1 seconds F97 Resin-moldedChip, High Reliability (High temperature / moisture resistance) Series SOLID TANTALUM ELECTROLYTIC CAPACITORS Type numbering system (Example : 16V 3.3 µF) Dimensions Marking Standard ratings Drawing Specifications Taping code (Refer to page 267 for details) F 1 9 2 7 3 1 4 C 5 3 6 3 7 5 8 M 9 B 10 11 Case code Capacitance tolerance Rated Capacitance Rated voltage Series C • N Case A • B Case L H S W1 W2 S L H S W1 W2 S A Case B Case C Case C105 3.3 16r Rated voltage (Voltage code) Rated Capacitance (Capacitance code ) Rated voltage (V) Rated Capacitance (µF) Rated Voltage (V) Month code Month code N Case 0.33 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 334 474 684 105 155 225 335 475 685 106 156 226 336 476 686 107 157 A A A B B B C C C • N N N A A A B B B C C C • N N N A A A B B B C C C • N N A A A B B B C C C • N N A A A B B B C C N N A A A B B B C C C • N N A A A B B B C C N N 4 0G 6.3 0J 10 1A 16 1C 20 1D 25 1E 35 1V Code V Case code A B C N LW1 W2 HS (mm) 3.2 ± 0.2 3.5 ± 0.2 6.0 ± 0.2 7.3 ± 0.2 1.6 ± 0.2 2.8 ± 0.2 3.2 ± 0.2 4.3 ± 0.2 1.2 ± 0.1 2.2 ± 0.1 2.2 ± 0.1 2.4 ± 0.1 1.6 ± 0.2 1.9 ± 0.2 2.5 ± 0.2 2.8 ± 0.2 0.8 ± 0.2 0.8 ± 0.2 1.3 ± 0.2 1.3 ± 0.2 Cap. ( µF) Item --55 ~ +125˚C (Rated temperature : 85˚C.) Category Temperature Range Capacitance Tolerance Performance Characteristics ± 20%, ± 10% (at 120Hz) Leakage Current ∗ • After 1 minute' s application of rated voltage,leakage current at 20˚C is not more than 0.01CV or 0.5 µA, whichever is greater. • After 1 minute' s application of rated voltage,leakage current at 85˚C is not more than 0.1CV or 5 µA,whichever is greater. • After 1 minute' s application of derated voltage,leakage current at 125˚C is not more than 0.125CV or 6.3 µA,whichever is greater. Capacitance Change by Temperature +15% Max. (at +125˚C) +10% Max. (at +85˚C) --10% Max. (at --55˚C) Damp Heat At 85˚C, 85% R.H.,For 1000 hours (No voltage applied) Capacitance Change •••••• Within ±10% of initial value Dissipation Factor ••••••••••• Initial specified value or less Leakage Current •••••••••••• 125% or less of initial specified value Load Humidity After 500 hour' s application of rated voltage in series with a 33Ω resistor at 60˚C,90~95% R.H.,capacitors meet the characteristics requirements listed below. Capacitance Change •••••• Within ±10% of initial value Dissipation Factor •••••••••• Initial specified value or less Leakage Current •••••••••••• 125% or less of initial specified value Temperature Cycles At --55˚C / +125˚C,For 30 minutes each,1000 cycles Capacitance Change •••••• Within ± 5% of initial value Dissipation Factor ••••••••••• Initial specified value or less Leakage Current •••••••••••• • Initial specified value or less Resistance to Soldering Heat At 260˚C,reflowing capacitors for 10 seconds Max. Capacitance Change •••••• Within ± 5% of initial value Dissipation Factor ••••••••••• Initial specified value or less Leakage Current •••••••••••• • Initial specified value or less Solderability After immersing capacitors completely into a solder pot at 245˚C for 2~3 seconds,more than 3/4 of their electrode area shall remain covered with new solder. Surge ∗ After application of surge in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF,for 1000 successive test cycles at 85˚C,capacitors meet the characteristics requirements listed below. Capacitance Change •••••• Within ± 5% of initial value Dissipation Factor ••••••••••• Initial specified value or less Leakage Current •••••••••••• • Initial specified value or less Endurance ∗ After 2000 hours' application of rated voltage in series with a 3 Ω resistor at 85˚C,or derated voltage in series with a 3Ω resistor at 125˚C,capacitors meet the characteristic requirements listed below. Capacitance Change •••••• Within ±10% of initial value Dissipation Factor ••••••••••• Initial specified value or less Leakage Current •••••••••••• • Initial specified value or less Shear Test After Applying the pressure load of 5N for 10 ± 1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on an aluminum substrate,there shall be found neither exfoliation nor its sign at the terminal electrode. Terminal Strength Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with a specified jig at the center of the substrate so that the substrate may bend by 1mm as illustrated. Then,there shall be found no remarkable abnormality on the capacitor terminals. ∗ As for the surge and derated voltage at 125˚C, refer to page 266 for details. 45 45 R230 20 Dissipation Factor Refer to next page ESR (100kHz) Refer to next page Adapted to the RoHS directive (2002/95/EC). |
Similar Part No. - F971A225MAA |
|
Similar Description - F971A225MAA |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |