CAT.8100V

F98

Specifications

Type numbering system (Example : 6.3V 10 µF)

Drawing

L

H

M

1.6

± 0.1 0.85 ± 0.1 0.65 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 0.6 ± 0.1

(mm)

Cace Code

L

H

S

2.0

± 0.1 1.25 ± 0.1 0.9 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 1.0 ± 0.1

Rated voltage

(Voltage code)

J

Taping code

(Refer to page 267 for details)

F

1

9

2

8

3

0

4

J

5

1

6

0

7

6

8

M

9

M

10 11

Case code

Capacitance tolerance

Rated Capacitance Rated voltage

Series

Marking

Standard ratings

Category

Temperature Range

Capacitance Tolerance

Leakage Current

Dissipation Factor(120Hz)

Damp Heat

Temperature Cycles

Resistance to Soldering

Heat

Surge∗

Endurance∗

Shear Test

Terminal Strength

Performance Characteristics

±20% (at 120Hz)

Refer to the list below (* 1)

After 5 minute's application of rated voltage, leakage current at

20

°C is not more than 0.1CV or 0.5µA, whichever is greater.

At 40

°C, 90 ~ 95% R.H., For 500hours (No voltage applied)

Capacitance Change

Refor to the list below (* 1)

Dissipation Factor

150% or less of initial specified value

Leakage Current

200% or less of initial specified value

At --55

°C / +125°C, For 30 minutes each, 5 cycles

Capacitance Change

Refor to the list below (* 1)

Dissipation Factor

150% or less of initial specified value

Leakage Current

Initial specified value or less

At 260

°C, For 10 seconds, Reflow,

Capacitance Change

Refor to the list below (* 1)

Leakage Current

Initial specified value or less

Leakage Current

Initial specified value or less

After application of surge in series with a 1k

Ω resistor at the

rate of 30 seconds ON, 30 seconds OFF, for 1000 successive

test cycles at 85

°C, capacitors meet the characteristics

requirements listed below.

Capacitance Change

Refor to the list below (* 1)

Dissipation Factor

150% or less of initial specified value

Leakage Current

200% or less of initial specified value

After 1000 hours' application of rated voltage in series with a

3Ω resistor at 85°C, capacitors meet the characteristic

requirements listed below

Capacitance Change

Refor to the list below (* 1)

Dissipation Factor

150% or less of initial specified value

Leakage Current

200% or less of initial specified value

After applying the pressure load of 5N

for 10

±1 seconds horizontally to the

center of capacitor side body which has

no electrode and has been soldered

beforehand on an aluminum substrate,

there shall be found neither exfoliation

nor its sign at the terminal electrode.

Keeping a capacitor surface-mounted on a substrate upside

down and supporting the substrate at both of the opposite

bottom points 45mm apart from the center of the capacitor, the

pressure strength is applied with

a specified jig at the center of the

substrate so that the substrate

may bend by 1mm as illustrated.

Then, there shall be found no

remarkable abnormality on the

capacitor terminals.

Item

--55 ~ +125

°C (Rated temperature : 85°C)

ESR(100kHz)

Refer to the list below (* 1)

For 10

20

R230

45

45

Resin-molded Chip,

High Capacitance Series

∗ As for the surge and derated voltage at 125˚C, refer to page 266 for details.

SOLID TANTALUM ELECTROLYTIC CAPACITORS

( ) The series in parentheses are being developed.

Please contact to your local Nichicon sales office when

these series are being designed in your application.

4

7.5

4

4

7.5

6

6

6

7.5

6

7.5

4

6

10

10

12

4

10

± 30

± 30

± 30

± 30

± 30

± 30

± 30

± 30

± 30

± 30

± 30

± 20

± 30

± 30

± 30

± 30

± 20

± 30

30

15

30

30

20

8

20

25

6

6

20

20

30

6

6

12

18

6

47

22

33

68

4.7

10

22

47

2.2

4.7

10

22

33

1

2.2

4.7

10

1

Part Number

1.2

0.9

1.3

2.7

0.5

0.6

1.4

3.0

0.5

0.5

1.0

2.2

3.3

0.5

0.5

0.8

1.6

0.5

Leakage

Current

(µA)

ESR

(

Disspation

Factor

(% @120Hz)

Case

code

2.5

4

6.3

10

16

20

Rated Volt

(V)

Rated

Capacitance

(µF)

F980E476MMA

F980G226MMA

F980G336MMA

F980G686MSA

F980J475MMA

F980J106MMA

F980J226MMA

F980J476MSA

F981A225MMA

F981A475MMA

F981A106MMA

F981A226MSA

F981A336MSA

F981C105MMA

F981C225MMA

F981C475MMA

F981C106MSA

F981D105MMA

M

M

M

S

M

M

M

S

M

M

M

S

S

M

M

M

S

M

1

2.2

4.7

10

22

33

47

68

100

105

225

475

106

226

336

476

686

107

M

(S)

M

M

(M)

S

(S)

M

M

M

(M)

S

M

M

M

S

S

M

M

M

S

2.5

4

6.3

10

16

20

0E

0G

0J

1A

1C

1D

V

Code

Cap.(µF)

*1

∆C/C

(%)

Adapted to the RoHS directive (2002/95/EC).

M