 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
BQ2084DBT-V141 Datasheet(PDF) 9 Page - Texas Instruments |
|
||||||||||||||||||||||||||||||
BQ2084DBT-V141 Datasheet(HTML) 9 Page - Texas Instruments |
|
|
9 / 71 page  www.ti.com DIGITAL FILTER VOLTAGE CURRENT TEMPERATURE GAS GAUGE OPERATION General bq2084-V143 SLUS732 – SEPTEMBER 2006 FUNCTIONAL DESCRIPTION (continued) The bq2084-V143 does not measure charge or discharge counts below the digital filter threshold. The digital filter threshold is programmed in the Digital Filter DF 0x2c and should be set sufficiently high to prevent false signal detection with no charge or discharge flowing through the sense resistor. While monitoring SR1 and SR2 for charge and discharge currents, the bq2084-V143 monitors the individual series cell voltages through the bq29312. The bq2084-V143 configures the bq29312 to present the selected cell to the CELL pin of the bq29312, which should be connected to VIN of the bq2084-V143. The internal ADC of the bq2084-V143 then measures the voltage and scales it appropriately. The bq2084-V143 then reports the Voltage() and the individual cell voltages in VCELL1(), VCELL2(), VCELL3(), and VCELL4(). An additional SMBus command (0x45) returns the measured ADC Reading of the PACK input to the AFE. The bq2084-V143 uses the SR1 and SR2 inputs to measure and calculate the battery charge and discharge current. This value is reported via the SBS command Current(). AverageCurrent() is implemented as a single-pole IIR filter with a 14.5-s time constant. The TS input of the bq2084-V143 along with an NTC thermistor measures the battery temperature as shown in the schematic. The bq2084-V143 reports temperature via the SBS command Temperature(). The bq2084-V143 can also be configured to use its internal temperature sensor by setting the IT bit in Misc Configuration DF 0x2a-0x2b. Data flash locations DF 0xb5 through DF 0xc0 also have to be changed to prescribed values if the internal temperature sensor option is selected. Table 1. Data Flash Settings for Internal or External Temperature Sensor INTERNAL TEMP EXTERNAL TEMP SENSOR SETTING LOCATION SENSOR SETTING (Semitec 103AT) LABEL Dec (Hex) Dec (Hex) Dec (Hex) Misc. Config 42 (0x2a) Bit 7 = 1 Bit 7 = 0 TS Const1 A3 164/5 (0xb5/6) 0 (0x0000) –28285 (0x9183) TS Const2 A2 166/7 (0xb7/8) 0 (0x0000) 20848 (0x5170) TS Const3 A1 168/9 (0xb9/a) –11136 (0xd480) –7537 (0xe28f) TS Const4 A0 170/1 (0xbb/c) 5734 (0x1666) 4012 (0x0fac) Min Temp AD 172/3 (0xbd/e) 0 (0x0000) 0 (0x000) Max Temp 174/5 (0xbf/c0) 5734 (0x1666) 4012 (0x0fac) The operational overview in Figure 1 illustrates the gas gauge operation of the bq2084-V143. Table 3 describes the bq2084-V143 registers. 9 Submit Documentation Feedback |
Similar Part No. - BQ2084DBT-V141 |
|
Similar Description - BQ2084DBT-V141 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
