STM32F103C8T6 datasheet(13/67 Pages) STMICROELECTRONICS

Part #	STM32F103C8T6

Description	Performance line, ARM-based 32-bit MCU with Flash, USB, CAN, seven 16-bit timers, two ADCs and nine communication interfaces

Download	67 Pages

Scroll/Zoom	100%

Manufacturer	STMICROELECTRONICS [STMicroelectronics]

Direct Link	http://www.st.com

Logo

13 / 67 page

STM32F103xx

Description

13/67

Universal serial bus (USB)

The STM32F103xx performance line embeds a USB device peripheral compatible with the

USB Full-speed 12 Mbs. The USB interface implements a full speed (12 Mbit/s) function

interface. It has software configurable endpoint setting and suspend/resume support. The

dedicated 48 MHz clock source is generated from the internal main PLL.

GPIOs (general-purpose inputs/outputs)

Each of the GPIO pins can be configured by software as output (push-pull or open-drain), as

input (with or without pull-up or pull-down) or as peripheral alternate function. Most of the

GPIO pins are shared with digital or analog alternate functions. All GPIOs are high current-

capable.

The I/Os alternate function configuration can be locked if needed following a specific

sequence in order to avoid spurious writing to the I/Os registers.

I/Os on APB2 with up to 18 MHz toggling speed

ADC (analog to digital converter)

Two 12-bit Analog to Digital Converters are embedded into STM32F103xx performance line

devices and each ADC shares up to 16 external channels, performing conversions in single-

shot or scan modes. In scan mode, automatic conversion is performed on a selected group

of analog inputs.

Additional logic functions embedded in the ADC interface allow:

●

Simultaneous sample and hold

●

Interleaved sample and hold

●

Single shunt

The ADC can be served by the DMA controller.

An analog watchdog feature allows very precise monitoring of the converted voltage of one,

some or all selected channels. An interrupt is generated when the converted voltage is

outside the programmed thresholds.

The events generated by the standard timers (TIMx) and the Advanced Control timer (TIM1)

can be internally connected to the ADC start trigger, injection trigger, and DMA trigger

respectively, to allow the application to synchronize A/D conversion and timers.

Temperature sensor

The temperature sensor has to generate a linear voltage with any variation in temperature.

The conversion range is between 2 V < VDDA < 3.6 V. The temperature sensor is internally

connected to the ADC_IN16 input channel which is used to convert the sensor output

voltage into a digital value.

Serial wire JTAG debug port (SWJ-DP)

The ARM SWJ-DP Interface is embedded. and is a combined JTAG and serial wire debug

port that enables either a serial wire debug or a JTAG probe to be connected to the target.

The JTAG TMS and TCK pins are shared respectively with SWDIO and SWCLK and a

specific sequence on the TMS pin is used to switch between JTAG-DP and SW-DP.

Similar Part No. - STM32F103C8T6

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	STM32F103C8T6TR	1Mb / 92P	Medium-density performance line ARM-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces
	STM32F103C8T6TR	1Mb / 96P	Medium-density performance line ARM-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces
	STM32F103C8T6TR	1Mb / 116P	Medium-density performance line Arm®-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 com. interfaces Rev 18 March 2022
	STM32F103C8T6XXX	1Mb / 92P	Medium-density performance line ARM-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces
	STM32F103C8T6XXX	1Mb / 96P	Medium-density performance line ARM-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces

More results

Similar Description - STM32F103C8T6

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	STM32F103X6	1Mb / 84P	Performance line, ARM-based 32-bit MCU with Flash, USB, CAN, seven 16-bit timers, two ADCs and nine communication interfaces
	STM32F103X4	1Mb / 80P	Low-density performance line, ARM-based 32-bit MCU with 16 or 32 KB Flash, USB, CAN, 6 timers, 2 ADCs, 6 communication interfaces
	STM32F101X6	966Kb / 64P	Access line, advanced ARM-based 32-bit MCU with Flash memory, six 16-bit timers, ADC and seven communication interfaces
	STM32F101X6	1Mb / 74P	Access line, advanced ARM-based 32-bit MCU with Flash memory, six 16-bit timers, ADC and seven communication interfaces
	STM32F103XC	1Mb / 118P	Performance line, ARM-based 32-bit MCU with up to 512 KB Flash, USB, CAN, 11 timers, 3 ADCs and 13 communication interfaces
	STM32F103VDT6	1Mb / 130P	High-density performance line ARM-based 32-bit MCU with 256 to 512KB Flash, USB, CAN, 11 timers, 3 ADCs, 13 communication interfaces
	STM32F103XC	1Mb / 123P	High-density performance line ARM-based 32-bit MCU with 256 to 512KB Flash, USB, CAN, 11 timers, 3 ADCs, 13 communication interfaces
	STM32F103ZCH6	1Mb / 130P	High-density performance line ARM-based 32-bit MCU with 256 to 512KB Flash, USB, CAN, 11 timers, 3 ADCs, 13 communication interfaces
	STM32F103ZEH6	1Mb / 130P	High-density performance line ARM-based 32-bit MCU with 256 to 512KB Flash, USB, CAN, 11 timers, 3 ADCs, 13 communication interfaces
	STM32F103RCT7	1Mb / 130P	High-density performance line ARM-based 32-bit MCU with 256 to 512KB Flash, USB, CAN, 11 timers, 3 ADCs, 13 communication interfaces

More results

STM32F103C8T6 Datasheet(PDF) 13 Page - STMicroelectronics

STM32F103C8T6 Datasheet(HTML) 13 Page - STMicroelectronics

Similar Part No. - STM32F103C8T6

Similar Description - STM32F103C8T6

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

Datasheet Download

Link URL