 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
SP207EP Datasheet(PDF) 8 Page - Sipex Corporation |
|
||||||||||||||||||||||||||||||
SP207EP Datasheet(HTML) 8 Page - Sipex Corporation |
|
|
8 / 16 page  Date:05/26/2005 +5V High-Speed RS232 Transceivers © Copyright 2005 Sipex Corporation 8 Figure 5. Charge Pump — Phase 4 VCC = +5V +10V VSS Storage Capacitor VDD Storage Capacitor C1 C2 C3 C4 + + ++ – – – – SHUTDOWN MODE The SP200, SP206, SP206B, SP207B, SP211, SP211B and SP213 all feature a control input which will disable the device and reduce the power supply current to less than 10 µA, making the parts ideal for battery–powered systems. In the “shutdown” mode the receivers and trans- mitters will both be tri–stated. The V+ output of the charge pump will discharge to V CC, and the V– output will discharge to ground. Products with the WakeUp function can enable or disable the receivers during shutdown. For complete shutdown to occur and the 10 µA power drain to be realized, the following condi- tions must be met: SP200, SP206/B, SP207B and SP211/B: • +5V must be applied to the SD pin • ENABLE must be either 0V, +5.0V or not connected • the transmitter inputs must be either +5.0V or not connected • V CC must be +5V • Receiver inputs must be >0V and <+5V SP213: • 0V must be applied to the SD pin • ENABLE must be either 0V, +5.0V or not connected • the transmitter inputs must be either +5.0V or not connected • V CC must be +5V • Receiver inputs must be >0V and <+5V WAKEUP FUNCTION The SP206B, SP207B, SP211B and SP213 have a wake–up feature that keeps two or more re- ceivers in an enabled state when the device is in the shutdown mode. The SP213 has two receiv- ers active (R 4 and R5), while the SP207B and SP211B have all receivers active during shut- down. With only the receivers active during shutdown, the devices draw 5–10 µA of supply current. ENABLE The SP206/B, SP207/B, SP211 and SP213 all feature an enable input, which allows the re- ceiver outputs to be either tri–stated or enabled. This can be especially useful when the receiver is tied directly to a microprocessor data bus. For the SP206/B, SP207/B and SP211, enable is active low; that is, 0V applied to the ENABLE pin will enable the receiver outputs. For the SP213, enable is active high; that is, +5V ap- plied to the ENABLE pin will enable the re- ceiver outputs. SP213 Only Power Receiver SD EN SD EN Up/Down Outputs 00 11 Up Enable 01 10 Up Tri–state 10 01 Down Enable 11 00 Down Tri–state Table 2. Wake–Up Truth Table |
Similar Part No. - SP207EP |
|
Similar Description - SP207EP |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
