Electronic Components Datasheet Search |
|
MAX16011TAC-T Datasheet(PDF) 7 Page - Maxim Integrated Products |
|
MAX16011TAC-T Datasheet(HTML) 7 Page - Maxim Integrated Products |
7 / 12 page The MAX16013/MAX16014 can be configured as an overvoltage switch controller to turn on/off a load (see the Typical Application Circuit). When the programmed overvoltage threshold is tripped, the internal fast com- parator turns off the external p-channel MOSFET (P2), pulling GATE2 to VCC to disconnect the power source from the load. When the monitored voltage goes below the adjusted overvoltage threshold, the MAX16013 enhances GATE2, reconnecting the load to the power source (toggle ENABLE on the MAX16014 to reconnect the load). The MAX16013 can be configured as an overvoltage limiter switch by connecting the resistive divider to the load instead of VCC (Figure 3). See the Overvoltage Limiter section. Supply Voltage Connect a 5.5V to 72V supply to VCC for proper opera- tion. For noisy environments, bypass VCC to GND with a 0.1µF or greater capacitor. When VCC falls below the UVLO voltage the following states are present (Table 1). Hysteresis Hysteresis adds noise immunity to the voltage monitors and prevents oscillation due to repeated triggering when the monitored voltage is near the threshold trip voltage. The hysteresis in a comparator creates two trip points: one for the rising input voltage (VTH+) and one for the falling input voltage (VTH-). These thresholds are shown in Figure 4. Enable Inputs (EN or EN) The MAX16011 offers an active-high enable input (EN), while the MAX16010 offers both an active-high enable input (EN) and active-low enable input (EN). For the MAX16010, drive EN low or EN high to force the output low. When the device is enabled (EN = high and EN = low) the state of OUTA and OUTB depends on INA+ and INB- logic states. Ultra-Small, Overvoltage Protection/ Detection Circuits _______________________________________________________________________________________ 7 MAX16012 IN+ REF IN- OUT RPULLUP R1 R2 GND VBATT VCC OUT Figure 2. Typical Operating Circuit for the MAX16012 MAX16013 GATE1 SET GATE2 VCC GND P2 P1 R1 R2 VBATT Figure 3. Overvoltage Limiter Protection Table 1. UVLO State (VCC < VUVLO) PART OUTA OUTB OUT GATE2 MAX16010 Low Low — — MAX16011 Low Low, LOGIC = low High, LOGIC = high —— MAX16012 —— Low — MAX16013 MAX16014 —— — High VIN+ VOUT VTH+ VTH- VCC 0V VHYST tPROP tPROP tPROP Figure 4. Input and Output Waveforms |
Similar Part No. - MAX16011TAC-T |
|
Similar Description - MAX16011TAC-T |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |