Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.COM

X  

X9015UM8-2.7 Datasheet(PDF) 3 Page - Intersil Corporation

Part # X9015UM8-2.7
Description  Single Digitally Controlled Potentiometer
Download  11 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  INTERSIL [Intersil Corporation]
Direct Link  http://www.intersil.com/cda/home
Logo INTERSIL - Intersil Corporation

X9015UM8-2.7 Datasheet(HTML) 3 Page - Intersil Corporation

  X9015UM8-2.7 Datasheet HTML 1Page - Intersil Corporation X9015UM8-2.7 Datasheet HTML 2Page - Intersil Corporation X9015UM8-2.7 Datasheet HTML 3Page - Intersil Corporation X9015UM8-2.7 Datasheet HTML 4Page - Intersil Corporation X9015UM8-2.7 Datasheet HTML 5Page - Intersil Corporation X9015UM8-2.7 Datasheet HTML 6Page - Intersil Corporation X9015UM8-2.7 Datasheet HTML 7Page - Intersil Corporation X9015UM8-2.7 Datasheet HTML 8Page - Intersil Corporation X9015UM8-2.7 Datasheet HTML 9Page - Intersil Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 3 / 11 page
background image
3
FN8157.5
August 31, 2006
Pin Descriptions
RH/VH and RL/VL
The high (RH/VH) and low (RL/VL) terminals of the X9015 are
equivalent to the fixed terminals of a mechanical
potentiometer. The minimum voltage is VSS and the
maximum is VCC. The terminology of RL/VL and RH/VH
references the relative position of the terminal in relation to
wiper movement direction selected by the U/D input, and not
the voltage potential on the terminal.
R
W
/V
W
RW/Vw is the wiper terminal and is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the control inputs.
The wiper terminal series resistance is typically 200
Ω at
VCC=5V. At power up the wiper position is at Tap #15.
(VL/RL=Tap #0).
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the tap position is incremented or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the
counter in the direction indicated by the logic level on the U/D
input.
Chip Select (CS)
The device is selected when the CS input is LOW. When CS
is returned HIGH while the INC input is also HIGH the X9015
will be placed in the low power standby mode until the device
is selected once again.
Principles Of Operation
There are two sections of the X9015: the input control,
counter and decode section; and the resistor array. The input
control section operates just like an up/down counter. The
output of this counter is decoded to turn on a single electronic
switch connecting a point on the resistor array to the wiper
output. The resistor array is comprised of 31 individual
resistors connected in series.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions. If
the wiper is moved several positions, multiple taps are
connected to the wiper for tIW (INC to VW change). The
RTOTAL value for the device can temporarily be reduced by a
significant amount if the wiper is moved several positions.
When the device is powered-down, the wiper position is lost.
When power is restored, the wiper is set to Tap #15.
Instructions and Programming
The INC, U/D and CS inputs control the movement of the
wiper along the resistor array. With CS set LOW the device is
selected and enabled to respond to the U/D and INC inputs.
HIGH to LOW transitions on INC will increment or decrement
(depending on the state of the U/D input) a five bit counter.
The output of this counter is decoded to select one of thirty
two wiper positions along the resistive array.
The system may select the X9015, move the wiper and
deselect the device. The new wiper position will be maintained
until changed by the system or until a power-up/down cycle.
The state of U/D may be changed while CS remains LOW.
This allows the host system to enable the device and then
move the wiper up and down until the proper trim is attained.
Pin Names
SYMBOL
DESCRIPTION
RH/VH
High terminal
RW/VW
Wiper terminal
RL/VL
Low terminal
VSS
Ground
VCC
Supply voltage
U/D
Up/Down control input
INC
Increment control input
CS
Chip select control input
Mode Selection
CS
INC
U/D
MODE
LH
Wiper up
LL
Wiper down
HX
Standby mode
HX
X
Standby mode
LL
X
Normal mode
L
H
Wiper Up (not recommended)
LL
Wiper Down (not recommend-
ed)
X9015


Similar Part No. - X9015UM8-2.7

ManufacturerPart #DatasheetDescription
logo
Intersil Corporation
X9015UM8-2.7 INTERSIL-X9015UM8-2.7 Datasheet
308Kb / 11P
   Low Noise, Low Power Volatile
More results

Similar Description - X9015UM8-2.7

ManufacturerPart #DatasheetDescription
logo
Intersil Corporation
X9428 INTERSIL-X9428 Datasheet
349Kb / 20P
   Single Digitally Controlled Potentiometer
logo
Xicor Inc.
X9111 XICOR-X9111 Datasheet
156Kb / 21P
   Single Digitally-Controlled Potentiometer
logo
Intersil Corporation
X9428 INTERSIL-X9428_06 Datasheet
315Kb / 21P
   Single Digitally Controlled Potentiometer
X9110TV14 INTERSIL-X9110TV14 Datasheet
309Kb / 18P
   Single Digitally-Controlled Potentiometer
February 13, 2008
X9119TV14I INTERSIL-X9119TV14I Datasheet
284Kb / 17P
   Single Digitally-Controlled Potentiometer
July 9, 2008
X9429WS16 INTERSIL-X9429WS16 Datasheet
320Kb / 20P
   Single Digitally Controlled Potentiometer
October 13, 2008
X9118TV14IZ INTERSIL-X9118TV14IZ Datasheet
400Kb / 17P
   Single Digitally-Controlled Potentiometer
April 9, 2014
X9271UV14IZ INTERSIL-X9271UV14IZ Datasheet
523Kb / 18P
   Single, Digitally Controlled Potentiometer
July 18, 2014
X9314WSIZ INTERSIL-X9314WSIZ Datasheet
222Kb / 8P
   Single Digitally Controlled Potentiometer
July 24, 2014
logo
Xicor Inc.
X9428 XICOR-X9428 Datasheet
580Kb / 20P
   Single Digitally Controlled Potentiometer
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com