Electronic Components Datasheet Search |
|
SN65LVDS048ADG4 Datasheet(PDF) 3 Page - Texas Instruments |
|
|
SN65LVDS048ADG4 Datasheet(HTML) 3 Page - Texas Instruments |
3 / 11 page www.ti.com DISSIPATION RATING TABLE RECOMMENDED OPERATING CONDITIONS |V ID | 2 2.4 * |V ID | 2 ELECTRICAL CHARACTERISTICS SN65LVDS048A SLLS451B – SEPTEMBER 2000 – REVISED SEPTEMBER 2002 TA ≤ 25°C OPERATING FACTOR(1) TA = 85°C PACKAGE POWER RATING ABOVE TA = 25°C POWER RATING D 950 mW 7.6 mW/°C 494 mW PW 774 mW 6.2 mW/°C 402 mW (1) This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow. MIN NOM MAX UNIT VCC Supply voltage 3 3.3 3.6 V Receiver input voltage GND 3 V VIC Common-mode input voltage V VCC– 0.8 TA Operating free-air temperature –40 25 85 °C over recommended operating free-air temperature range (unless otherwise noted)(1) PARAMETER TEST CONDITIONS MIN TYP(2) MAX UNIT VIT+ Differential input high threshold voltage 100 VCM = 1.2 V, 0.05 V, 2.35 V(3) mV VIT– Differential input low threshold voltage –100 V(CMR) Common mode voltage range VID = 200 mV pk to pk(4) 0.1 2.3 V VIN = 2.8 V –20 ±1 20 µA VCC = 3.6 V or 0 V IIN Input current VIN = 0 V –20 ±1 20 µA VIN = 3.6 V, VCC = 0 V –20 ±1 20 µA IOH = -0.4 mA, VID = 200 mV 2.7 3.2 V VOH Output high voltage IOH = -0.4 mA, input terminated 2.7 3.2 V IOH = -0.4 mA, input shorted 2.7 3.2 V VOL Output low voltage IOL = 2 mA, VID = -200 mV 0.05 0.25 V IOS Output short circuit current Enabled, VOUT = 0 V(5) –65 –100 mA IO(Z) Output 3-state current Disabled, VOUT = 0 V or VCC –1 1 µA VIH Input high voltage 2.0 VCC V VIL Input low voltage GND 0.8 V VIN = 0 V or VCC, II Input current (enables) –10 10 µA Other input = VCC or GND VIK Input clamp voltage ICL = –18 mA –1.5 –0.8 V ICC No load supply current, receivers enabled EN = VCC, Inputs open 8 15 mA ICC(Z) No load supply current, receivers disabled EN = GND, Inputs open 0.6 1.5 mA (1) Current into device pin is defined as positive. Current out of the device is defined as negative. All voltages are referenced to ground, unless otherwise specified. (2) All typical values are at 25°C and with a 3.3-V supply. (3) VCC is always higher than RIN+ and RIN- voltage, RIN- and RIN+ have a voltage range of -0.2 V to VCC-VID/2. To be compliant with ac specifications the common voltage range is 0.1 V to 2.3 V. (4) The VCMR range is reduced for larger VID, Example: If VID = 400 mV, the VCMR is 0.2 V to 2.2 V. The fail-safe condition with inputs shorted is not supported over the common-mode range of 0 V to 2.4 V, but is supported only with inputs shorted and no external common-mode voltage applied. A VID up to VCC-0 V may be applied to the RIN+ and RIN- inputs with the common-mode voltage set to VCC/2. Propagation delay and differential pulse skew decrease when VID is increased from 200 mV to 400 mV. Skew specifications apply for 200 mV < VID < 800 mV over the common-mode range. (5) Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time. Do not exceed maximum junction temperature specification. 3 Submit Documentation Feedback |
Similar Part No. - SN65LVDS048ADG4 |
|
Similar Description - SN65LVDS048ADG4 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |