Electronic Components Datasheet Search |
|
NJ88C33 Datasheet(PDF) 2 Page - Zarlink Semiconductor Inc |
|
NJ88C33 Datasheet(HTML) 2 Page - Zarlink Semiconductor Inc |
2 / 14 page NJ88C33 2 PIN DESIGNATIONS Description Pin Name V DD RI S/D SDA SCL PORT MOD FI GND2 FVN GND1 PD C LD Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Supply voltage (normally 5V or 3V). Reference frequency input from an accurate source, normally a crystal oscillator. The input is normally an AC coupled sinewave but may be a DC coupled square wave. Single/dual modulus operating mode selection input. Single modulus operation is selected by driving the pin low. 'High' selects dual modulus mode. I2C bus data input pin. It is also an open-drain output for generating I2C bus acknowledge pulses. I2C bus clock input. It can be clocked at up to 5MHz. Output control pin, which can be programmed via the I2C bus. It can be connected to the S/D pin to select single or dual modulus mode under bus control. Modulus control pin. It is high in single modulus mode but switches in dual modulus operation. In dual modulus mode, MOD remains low during operation of the A counter until A=0; MOD then remains high until N=0, when both counters are reloaded. It can be programmed via the I2C bus as an open-drain or push-pull output. Frequency input from a VCO or prescaler. The input is normally an AC coupled sinewave but may be a DC coupled square wave. Dedicated ground for the FI input buffer. It should be connected to the VCO ground or the prescaler ground, if used. Any noise on this pin will affect the performance of the VCO loop. Open-drain output from the N counter. Ground supply pin (global). Tristate current output from the phase detector. The polarity of the output can be programmed via the I2C bus. Voltage doubler output. The operation of the doubler can be controlled via the I2C bus. In applications where the voltage doubler is switched off, this pin should be connected to GND1; a reservior capacitor should be connected from this pin to GND1 for applications where it is switched on. Open-drain lock detect output - requires integration if used. OPERATING RANGE Test conditions (unless otherwise stated): PLL locked, RI = 10MHz Supply voltage Ambient temperature Supply current Single modulus Dual modulus Standby mode Standby mode V °C mA mA µA mA V DD T amb I DD I DD I DD I DD 2.5 -40 Conditions Symbol Min. Typ. Max. Unit Value 5 2.1 2 1.0 5.5 +85 3.0 3.0 1 1.5 Characteristic FI = 50MHz, VFI = 150mVrms, N,R > 1000 without voltage doubler, VDD = 5V, Tamb = 25°C FI = 10MHz, VFI = 500mVrms, N,R > 1000 without voltage doubler, VDD = 5V, Tamb = 25°C FI = 50MHz, VFI = 150mVrms, preamp off, divider off, VDD = 5V, Tamb = 25°C FI = 50MHz, VFI = 150mVrms, preamp on, divider off, VDD = 5V, Tamb = 25°C |
Similar Part No. - NJ88C33 |
|
Similar Description - NJ88C33 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |