Electronic Components Datasheet Search |
|
MIC29371-5.0BT Datasheet(PDF) 8 Page - Micrel Semiconductor |
|
MIC29371-5.0BT Datasheet(HTML) 8 Page - Micrel Semiconductor |
8 / 12 page MIC2937A/29371/29372 Micrel, Inc. MIC2937A/29371/29372 8 May 2006 Applications Information External Capacitors A10µF(orgreater)capacitorisrequiredbetweentheMIC2937A outputandgroundtopreventoscillationsduetoinstability.Most types of tantalum or aluminum electrolytics will be adequate; film types will work, but are costly and therefore not recom- mended. Many aluminum electrolytics have electrolytes that freeze at about –30°C, so solid tantalums are recommended for operation below –25°C. The important parameters of the capacitor are an effective series resistance of about 5Ω or less and a resonant frequency above 500kHz. The value of this capacitor may be increased without limit. At lower values of output current, less output capacitance is required for output stability. The capacitor can be reduced to 0.5µF for current below 10mA or 0.15µF for currents below 1 mA. Adjusting the MIC29372 to voltages below 5V runs the error amplifier at lower gains so that more output capacitance is needed. For the worst-case situation of a 750mA load at 1.23V output (Output shorted to Adjust) a 22µF (or greater) capacitor should be used. TheMIC2937A/29371willremaininregulationwithaminimum load of 5mA. When setting the output voltage of the MIC29372 versionwithexternalresistors,thecurrentthroughtheseresis- tors may be included as a portion of the minimum load. A 0.1µF capacitor should be placed from the input to ground if there is more than 10 inches of wire between the input and the AC filter capacitor or if a battery is used as the input. Error Detection Comparator Output (MIC29371) A logic low output will be produced by the comparator when- ever the MIC29371 output falls out of regulation by more than approximately 5%. This figure is the comparator’s built-in offset of about 75mV divided by the 1.235V reference volt- age. (Refer to the block diagram on Page 1). This trip level remains “5% below normal” regardless of the programmed output voltage of the MIC29371. For example, the error flag trip level is typically 4.75V for a 5V output or 11.4V for a 12V output. The out of regulation condition may be due either to low input voltage,extremely high input voltage, current limit- ing, or thermal limiting. Figure 1 is a timing diagram depicting the ERROR signal and the regulated output voltage as the MIC29371 input is ramped up and down.The ERROR signal becomes valid (low) at about 1.3V input. It goes high at about 5V input (the input voltage at which V OUT = 4.75). Since the MIC29371’s dropout voltage is load-dependent (see curve in Typical Performance Characteristics), the input voltage trip point (about 5V) will vary with the load current. The output voltage trip point (ap- proximately 4.75V) does not vary with load. * SEE APPLICATIONS INFORMATION Figure 1. ERROR Output Timing TheerrorcomparatorhasanNPNopen-collectoroutputwhich requires an external pull-up resistor. Depending on system requirements, this resistor may be returned to the 5V output or some other supply voltage. In determining a value for this resistor, note that while the output is rated to sink 250µA, this sink current adds to battery drain in a low battery condition. Suggested values range from 100k to 1MΩ. The resistor is not required if this output is unused. Programming the Output Voltage (MIC29372) The MIC29372 may programmed for any output voltage be- tween its 1.235V reference and its 26V maximum rating. An external pair of resistors is required, as shown in Figure 3. The complete equation for the output voltage is V OUT = V REF x { 1 + R1/R2 } – |IFB| R1 where V REF is the nominal 1.235 reference voltage and IFB is theAdjust pin bias current, nominally 20nA.The minimum rec- ommended load current of 1µAforces an upper limit of 1.2MΩ on the value of R 2, if the regulator must work with no load (a condition often found in CMOS in standby), I FB will produce a –2% typical error in V OUT which may be eliminated at room temperature by trimming R 1. For better accuracy, choosing R 2 = 100k reduces this error to 0.17% while increasing the resistorprogramcurrentto12µA.SincetheMIC29372typically draws 100µA at no load with SHUTDOWN open-circuited, this is a negligible addition. Reducing Output Noise In reference applications it may be advantageous to reduce the AC noise present at the output. One method is to reduce the regulator bandwidth by increasing the size of the output capacitor.Thisisrelativelyinefficient,asincreasingthecapaci- tor from 1µF to 220µF only decreases the noise from 430µV to 160µV RMS for a 100kHz bandwidth at 5V output. Noise can be reduced by a factor of four with the adjustable regulators * * OUTPUT VOLTAGE INPUT VOLTAGE ERROR NOT VALID NOT VALID 5V 1.3V 4.75V |
Similar Part No. - MIC29371-5.0BT |
|
Similar Description - MIC29371-5.0BT |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |