Electronic Components Datasheet Search |
|
OPA1632 Datasheet(PDF) 6 Page - Texas Instruments |
|
OPA1632 Datasheet(HTML) 6 Page - Texas Instruments |
6 / 15 page OPA1632 SBOS286A − DECEMBER 2003 − REVISED SEPTEMBER 2006 www.ti.com 6 APPLICATIONS INFORMATION Figure 1 shows the OPA1632 used as a differential-output driver for the PCM1804 high-performance audio ADC. Supply voltages of ±15V are commonly used for the OPA1632. The relatively low input voltage swing required by the ADC allows use of lower power-supply voltage, if desired. Power supplies as low as ±8V can be used in this application with excellent performance. This reduces power dissipation and heat rise. Power supplies should be bypassed with 10 µF tantalum capacitors in parallel with 0.1 µF ceramic capacitors to avoid possible oscillations and instability. The VCOM reference voltage output on the PCM1804 ADC provides the proper input common-mode reference voltage (2.5V). This VCOM voltage is buffered with op amp A2 and drives the output common-mode voltage pin of the OPA1632. This biases the average output voltage of the OPA1632 to 2.5V. The signal gain of the circuit is generally set to approximately 0.25 to be compatible with commonly-used audio line levels. Gain can be adjusted, if necessary, by changing the values of R1 and R2. The feedback resistor values (R3 and R4) should be kept relatively low, as indicated, for best noise performance. R5, R6, and C3 provide an input filter and charge glitch reservoir for the ADC. The values shown are generally satisfactory. Some adjustment of the values may help optimize performance with different ADCs. It is important to maintain accurate resistor matching on R1/R2 and R3/R4 to achieve good differential signal balance. Use 1% resistors for highest performance. When connected for single-ended inputs (inverting input grounded, as shown in Figure 1), the source impedance must be low. Differential input sources must have well-balanced or low source impedance. Capacitors C1, C2, and C3 should be chosen carefully for good distortion performance. Polystyrene, polypropylene, NPO ceramic, and mica types are generally excellent. Polyester and high-K ceramic types such as Z5U can create distortion. R 5 40 Ω R 1 1k Ω R 2 1k Ω 1k Ω R 4 270 Ω R 3 270 Ω R 6 40 Ω C 2 1nF C 1 1nF 0.1 µF 0.1 µF 10 µF V+ +8V to +16V −8V to −16V V − 1/2 PCM1804 V OCM 3 5 4 6 7 1 2 8 C 3 2.7nF V COM (2.5V) Enable(1) Balanced or Single−Ended Input OPA1632 OPA134 + 10 µF 0.1 µF + − NOTE: (1) Leave open to enable. Logic signals referenced to V − supply. See the Shutdown Function section. Figure 1. ADC Driver for Professional Audio |
Similar Part No. - OPA1632_07 |
|
Similar Description - OPA1632_07 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |