Specifications are subject to change without notice.

Customers should verify actual device performance in their specific applications.

Performance Characteristics (Tests According to MIL-STD-202, MIL-R-55342B, EIA RS-396)

Test

Procedure

Method

Specification

Deviation from Nominal

1 %

5 %

DC Resistance

—

MIL-STD-202 303

MIL-R-55342D 4.7.2

F:≤±1 %

≤±5.0 %

EIA RS-396 4.4

Thermal Shock

-40 °C, 60 minutes;

MIL-STD-202 107

MIL-R-55342D 4.7.3

≤±0.5 % +0.05 Ω≤±1 % +0.05 Ω

+125 °C, 60 minutes

EIA RS-396 4.5

Low Temperature

-55 °C, 1 hour off;

MIL-R-55342D 4.7.4

MIL-R-55342D 4.7.4

≤±0.5 % 0.05 Ω≤±1.0 % +0.05 Ω

Operation

45 minutes on

EIA RS-396 4.6

Short Time

Rated Voltage x 2.5;

MIL-R-55342D 4.7.5

MIL-R-55342D 4.7.5

≤±1 % +0.05 Ω≤±2.0 % +0.05 Ω

Overload

5 seconds

EIA RS-396 4.7

CR0603: 100 V max.

CR0805; 300 V max.

CR1206: 400 V max.

High Temperature

+125 °C; 1000 hours

MIL-R-55342D 4.7.6

MIL-R-55342D 4.7.6

≤±1.0 % +0.05 Ω≤+2.0 % +0.1 Ω

Exposure

EIA RS-396 4.8

Resistance to

260 °C, 10 seconds

MIL-R-55342D 4.7.7

MIL-R-55342D 4.7.7

≤±0.5 % +0.05 Ω≤±1.0 % +0.05 Ω

Soldering Heat

Moisture

90-98 %RH; 10 cycles

MIL-STD-202 106D

MIL-R-55342D 4.7.8

≤±0.5 % +0.05 Ω≤±2.0 % +0.05 Ω

Resistance

EIA RS-396 4.9

Load Life

+70 °C; 1.5 hours on,

MIL-STD-202 108

MIL-R-55342D 4.7.10

≤±1.0 % +0.05 Ω≤±3.0 % +0.1 Ω

1000 Hours

0.5 hours off;

Condition D

1000 hours

EIA RS-396 4.12

Solderability

+235 °C; 3 seconds

MIL-STD-202 208

MIL-R-55342D 4.7.11

≥95 % of area

≥95 % of area

EIA RS-396 4.11

covered

covered

Terminal Strength

Pull Test

MIL-R-55342D 4.7.12

MIL-R-55342D 4.7.12

≥500 g

≥500 g

Current Noise

Quan-Tech Model 315B

MIL-STD-202 308

MIL-R-55342D 6.6

R≤1k Ω; max. 1 µV/V

R≤1k Ω; max. 1 µV/V

R≤10k Ω; max. 3 µV/V

R≤10k Ω; max. 3 µV/V

R≤100k Ω; max. 6 µV/V

R≤100k Ω; max. 6 µV/V

R≤1M Ω; max. 10 µV/V

R≤2M Ω; max. 10 µV/V

Humidity,

+40 °C; 90-95 % RH,

MIL-STD-202 103B

—

≤±2.5 % +0.05 Ω≤±2.5 % +0.05 Ω

Steady State

1344 Hours

Condition D

Salt Spray

96 hours

MIL-STD-202 101D

—

≤±1.0 % +0.2 Ω≤±1.0 % +0.1 Ω

Condition A

Vibration

10-2000 Hz, 6 hours

MIL-STD-202 201A

—

≤±0.5 % +0.1 Ω≤±1.0 % +0.1 Ω

Voltage Coefficient

—

MIL-STD-202 309

—

≤100 ppm/V

≤100 ppm/V

Insulation

Test Potential 500V

MIL-STD-202 302

—

≥10

3

Resistance

CR0603: 100V

Condition B

Dielectric

—

MIL-STD-202 301

—

≥500 V (CR1206, CR0805)

Withstanding

≥300 V (CR0603)

Voltage

Drop Test

1 m

MIL-STD-202 203B

—

≤±0.5 % +0.1 Ω≤±1.0 % +0.1 Ω

Bending Test

5 mm/90 mm; 10 sec.

—

—

≤±1 % +0.05 Ω≤±1.0 % +0.05 Ω

CR0603/CR0805/CR1206 - Chip Resistors