No.

Item

Specifications

Test Method

Temperature

Compensating Type

High Dielectric Type

16

Humidity

(Steady

State)

The measured and observed characteristics should satisfy the

specifications in the following table

Set the capacitor at 40

T2D and in 90 to 95% humiduty for

500

T12 hours.

Remove and set for 24

T2 hours (temperature compensating

type) or 48

T4 hours (high dielectric constant type) at room

temperature, then measure.

Appearance

No defects or abnormalities

Capacitance

Change

Within

T5% or T0.5pF

(Whichever is larger)

B1, B3, R1, R6, R7, C8

: Within

T12.5%

F1, F5 : Within

T30%

Q/D.F.

30pF and over : Q

U350

10pF and over

30pF and below :

Q

U275W2.5C

10pF and below :

Q

U200W10C

C : Nominal Capacitance (pF)

[B1, B3, R1, R6, R7, E4]

W.V. : 25Vmin. : 0.05max.

W.V. : 16/10V : 0.05max.

W.V. : 6.3V/4V

: 0.075max. (C

F3.3µF)

: 0.125max. (C

U3.3µF)

[F1, F5]

W.V. : 25Vmin.

: 0.075max. (C

F0.1µF)

: 0.125max. (C

U0.1µF)

W.V. : 16V/10V : 0.15max.

W.V. : 6.3V : 0.2max.

I.R.

More than 1,000M

Ω or 50Ω • F (Whichever is smaller)

Continued from the preceding page.

Continued on the following page.

Temperature

Cycle

15

Fix the capacitor to the supporting jig in the same

manner and under the same conditions as (10).

Perform the five cycles according to the four heat treatments

shown in the following table.

Set for 24

T2 hours (temperature compensating type) or 48T4

hours (high dielectric constant type) at room temperature, then

measure.

#Initial measurement for high dielectric constant type

Perform a heat treatment at 150

W0/Y10D for one hour and

then set at room temperature for 48

T4 hours.

Perform the initial measurement.

No defects or abnormalities

Within

T2.5% or T0.25pF

(Whichever is larger)

B1, B3, R1, R6, R7

: Within

T7.5%

F1, F5, E4 : Within

T20%

Appearance

Capacitance

Change

The measured and observed characteristics should safisfy the

specifications in the following table

More than 10,000M

Ω or 500Ω • F (Whichever is smaller)

30pF and over : Q

U1000

30pF and below :

Q

U400W20C

C : Nominal Capacitance (pF)

[B1, B3, R1, R6, R7, E4]

W.V. : 25Vmin. : 0.025max.

W.V. : 16/10V : 0.035max.

W.V. : 6.3V/4V

: 0.05max. (C

F3.3µF)

: 0.1max. (C

U3.3µF)

[F1, F5]

W.V. : 25Vmin.

: 0.05max. (C

F0.1µF)

: 0.09max. (C

U0.1µF)

W.V. : 16V/10V : 0.125max.

W.V. : 6.3V : 0.15max.

I.R.

No defects

Dielectric

Strength

Q/D.F.

Step

1234

Temp. (

D)

Time (min.)

Min.

Operating

Temp.

W0/Y3

Room

Temp.

Max.

Operating

Temp.

W3/Y0

Room

Temp.

30

T3

2 to 3

30

T3

2 to 3

before ordering. Especially, please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in them to prevent smoking and/or burning, etc.

• You are able to read a detailed specification in the website (http://search.murata.co.jp/) before to require our product specification or to transact the approval sheet for product specification.

Capacitors