W3H64M72E-XSBX

10

White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com

White Electronic Designs

March 2006

Rev. 1

ADVANCED*

White Electronic Designs Corp. reserves the right to change products or specifications without notice.

TABLE 2 – BURST DEFINITION

NOTES:

1.

For a burst length of two, A1-Ai select two-data-element block; A0 selects the

starting column within the block.

2.

For a burst length of four, A2-Ai select four-data-element block; A0-1 select the

starting column within the block.

3.

For a burst length of eight, A3-Ai select eight-data-element block; A0-2 select the

starting column within the block.

4.

Whenever a boundary of the block is reached within a given sequence above, the

following access wraps within the block.

Burst

Length

Starting Column

Address

Order of Accesses Within a Burst

Type = Sequential

Type = Interleaved

4

A1

A0

0

0

0-1-2-3

0-1-2-3

0

1

1-2-3-0

1-0-3-2

1

0

2-3-0-1

2-3-0-1

1

1

3-0-1-2

3-2-1-0

8

A2

A1

A0

0

0

0

0-1-2-3-4-5-6-7

0-1-2-3-4-5-6-7

0

0

1

1-2-3-0-5-6-7-4

1-0-3-2-5-4-7-6

0

1

0

2-3-0-1-6-7-4-5

2-3-0-1-6-7-4-5

0

1

1

3-0-1-2-7-4-5-6

3-2-1-0-7-6-5-4

1

0

0

4-5-6-7-0-1-2-3

4-5-6-7-0-1-2-3

1

0

1

5-6-7-4-1-2-3-0

5-4-7-6-1-0-3-2

1

1

0

6-7-4-5-2-3-0-1

6-7-4-5-2-3-0-1

1

1

1

7-4-5-6-3-0-1-2

7-6-5-4-3-2-1-0

OPERATING MODE

The normal operating mode is selected by issuing a

command with bit M7 set to “0,” and all other bits set to

the desired values, as shown in Figure 5. When bit M7 is

“1,” no other bits of the mode register are programmed.

Programming bit M7 to “1” places the DDR2 SDRAM into a

test mode that is only used by the manufacturer and should

not be used. No operation or functionality is guaranteed

if M7 bit is ‘1.’

DLL RESET

DLL RESET is defined by bit M8, as shown in Figure 5.

Programming bit M8 to “1” will activate the DLL RESET

function. Bit M8 is self-clearing, meaning it returns back

to a value of “0” after the DLL RESET function has been

issued.

Anytime the DLL RESET function is used, 200 clock cycles

must occur before a READ command can be issued to

allow time for the internal clock to be synchronized with

the external clock. Failing to wait for synchronization

parameters.

WRITE RECOVERY

Write recovery (WR) time is defined by bits M9–M11, as

shown in Figure 5. The WR register is used by the DDR2

SDRAM during WRITE with auto precharge operation.

During WRITE with auto precharge operation, the DDR2

SDRAM delays the internal auto precharge operation by

WR clocks (programmed in bits M9–M11) from the last

data burst.

WR values of 2, 3, 4, 5, or 6 clocks may be used for

programming bits M9–M11. The user is required to

program the value of WR, which is calculated by dividing

Reserved states should not be used as unknown operation

or incompatibility with future versions may result.

POWER-DOWN MODE

Active power-down (PD) mode is defined by bit M12,

as shown in Figure 5. PD mode allows the user to

determine the active power-down mode, which determines

performance versus power savings. PD mode bit M12 does

not apply to precharge PD mode.

When bit M12 = 0, standard active PD mode or “fast-exit”

for fast-exit active PD exit timing. The DLL is expected to

be enabled and running during this mode.

When bit M12 = 1, a lower-power active PD mode or “slow-

used for slow-exit active PD exit timing. The DLL can be

enabled, but “frozen” during active PD mode since the exit-

to-READ command timing is relaxed. The power difference

expected between PD normal and PD low-power mode is