87

244

200

2000

5.1

MIW5049

87

243

{33

{333

{15

MIW5047

88

236

{42

{416

{12

MIW5046

87

239

66.6

666

15

MIW5044

87

240

83

833

12

MIW5043

87

239

200

2000

5

MIW5042

85

243

300

3000

3.3

MIW5041

83

40

10

188

300

3000

2.5

48

( 36 ~ 75 )

MIW5040

87

489

200

2000

5.1

MIW5039

87

478

{33

{333

{15

MIW5037

88

473

{42

{416

{12

MIW5036

87

478

66.6

666

15

MIW5034

87

479

83

833

12

MIW5033

87

479

200

2000

5

MIW5032

85

485

300

3000

3.3

MIW5031

83

40

20

377

300

3000

2.5

24

( 18 ~ 36 )

MIW5030

83

1024

200

2000

5.1

MIW5029

86

968

{33

{333

{15

MIW5027

87

957

{42

{416

{12

MIW5026

86

968

66.6

666

15

MIW5024

87

957

83

833

12

MIW5023

83

1004

200

2000

5

MIW5022

82

60

40

1006

300

3000

3.3

12

( 9 ~ 18 )

MIW5021

% (Typ.)

mA (Typ.)

mA (Typ.)

mA (Typ.)

mA

mA

VDC

VDC

@Max. Load

@No Load

@Max. Load

Min.

Max.

Efficiency

Reflected

Ripple

Current

Input Current

Output Current

Output

Voltage

Input

Voltage

Model

Number

Model Selection Guide

EN55022 Class A

Conducted EMI

Free-Air Convection

Cooling

%

95

---

Humidity

]

+125

-40

Storage Temperature

]

+90

-40

Case

Operating Temperature

]

+60

-40

Ambient

Operating Temperature

Unit

Max.

Min.

Conditions

Parameter

Environmental Specifications

Exceeding the absolute maximum ratings of the unit could cause damage.

These are not continuous operating ratings.

mW

2,500

---

Internal Power Dissipation

]

260

---

Lead Temperature (1.5mm from case for 10 Sec.)

VDC

100

-0.7

48VDC Input Models

VDC

50

-0.7

24VDC Input Models

VDC

25

-0.7

12VDC Input Models

Input Surge Voltage

( 1000 mS )

Unit

Max.

Min.

Parameter

Notes :

1. Specifications typical at Ta=+25], resistive load,

nominal input voltage, rated output current unless

otherwise noted.

2. Transient recovery time is measured to within 1%

error band for a step change in output load of 75%

to 100%.

3. Ripple & Noise measurement bandwidth is 0-20

MHz.

4. These power converters require a minimum output

loading to maintain specified regulation.

5. Operation under no-load conditions will not

damage these modules; however, they may not

meet all specifications listed.

6. All DC/DC converters should be externally fused

on the front end for protection.

7. Other input and output voltage may be available,

please contact factory.

8. Specifications subject to change without notice.

Absolute Maximum Ratings

MIW5000 Series

2

MINMAX

REV:0 2005/04