77

57

{17

{67

{15

MDW1047

77

57

{21

{83

{12

MDW1046

71

62

{50

{200

{5

MDW1045

79

55

33

134

15

MDW1044

79

53

42

167

12

MDW1043

73

57

100

400

5

MDW1042

71

10

8

49

125

500

3.3

48

( 36 ~ 72 )

MDW1041

80

110

{17

{67

{15

MDW1037

78

112

{21

{83

{12

MDW1036

74

119

{50

{200

{5

MDW1035

81

108

33

134

15

MDW1034

80

109

42

167

12

MDW1033

77

109

100

400

5

MDW1032

72

15

10

96

125

500

3.3

24

( 18 ~ 36 )

MDW1031

78

226

{17

{67

{15

MDW1027

78

224

{21

{83

{12

MDW1026

73

242

{50

{200

{5

MDW1025

80

220

33

134

15

MDW1024

80

209

42

167

12

MDW1023

77

217

100

400

5

MDW1022

73

25

20

184

125

500

3.3

12

( 9 ~ 18 )

MDW1021

71

598

{17

{67

{15

MDW1017

69

615

{21

{83

{12

MDW1016

64

667

{50

{200

{5

MDW1015

73

582

33

134

15

MDW1014

75

534

42

167

12

MDW1013

73

548

100

400

5

MDW1012

70

100

40

471

125

500

3.3

5

( 4.5 ~ 9 )

MDW1011

% (Typ.)

mA (Typ.)

mA (Typ.)

mA (Typ.)

mA

mA

VDC

VDC

@Max. Load

@No Load

@Max. Load

Min.

Max.

Efficiency

Reflected

Ripple

Current

Input Current

Output Current

Output

Voltage

Input

Voltage

Model

Number

Model Selection Guide

Free-Air Convection

Cooling

%

95

---

Humidity

]

+125

-40

Storage Temperature

]

+90

-40

Case

Operating Temperature

]

+65

-40

Ambient

Operating Temperature

Unit

Max.

Min.

Conditions

Parameter

Environmental Specifications

Exceeding these values can damage the module. These are not continuous

operating ratings.

mW

1,800

---

Internal Power Dissipation

]

260

---

Lead Temperature (1.5mm from case for 10 Sec.)

VDC

100

-0.7

48VDC Input Models

VDC

50

-0.7

24VDC Input Models

VDC

25

-0.7

12VDC Input Models

VDC

11

-0.7

5VDC Input Models

Input Surge Voltage

( 1000 mS )

Unit

Max.

Min.

Parameter

Note :

1. Specifications typical at Ta=+25], resistive load,

nominal input voltage, rated output current unless

otherwise noted.

2. Transient recovery time is measured to within 1%

error band for a step change in output load of 50%

to 100%.

3. Ripple & Noise measurement bandwidth is 0-20

MHz.

4. These power converters require a minimum

output loading to maintain specified regulation.

5. Operation under no-load conditions will not

damage these devices; however they may not

meet all listed specifications.

6. All DC/DC converters should be externally fused

on the front end for protection.

7. Other input and output voltage may be available,

please contact factory.

8. Specifications subject to change without notice.

Absolute Maximum Ratings

MDW1000 Series