ICS8534AY-01T datasheet(8/17 Pages) ICST

Part #	ICS8534AY-01T

Description	LOW SKEW, 1-TO-22 DIFFERENTIAL-TO-3.3V LVPECL FANOUT BUFFER

Download	17 Pages

Scroll/Zoom	100%

Manufacturer	ICST [Integrated Circuit Systems]

Direct Link	http://www.icst.com

Logo

8 / 17 page

8534AY-01

www.icst.com/products/hiperclocks.html

REV. A NOVEMBER 19, 2004

8

Integrated

Circuit

Systems, Inc.

ICS8534-01

LOW SKEW, 1-TO-22

DIFFERENTIAL-TO-3.3V LVPECL FANOUT BUFFER

APPLICATION INFORMATION

Figure 2 shows how the differential input can be wired to accept

single ended levels. The reference voltage V_REF = V

CC/2 is

generated by the bias resistors R1, R2 and C1. This bias circuit

should be located as close as possible to the input pin. The ratio

FIGURE 2. SINGLE ENDED SIGNAL DRIVING DIFFERENTIAL INPUT

WIRING THE DIFFERENTIAL INPUT TO ACCEPT SINGLE ENDED LEVELS

of R1 and R2 might need to be adjusted to position the V_REF in

the center of the input voltage swing. For example, if the input

clock swing is only 2.5V and V

CC = 3.3V, V_REF should be 1.25V

and R2/R1 = 0.609.

R2

1K

V

CC

CLK_IN

+

-

R1

1K

C1

0.1uF

V_REF

V

CC - 2V

50

Ω

50

Ω

RTT

Z

o = 50Ω

Z

o = 50Ω

FOUT

FIN

RTT =

Z

o

1

((V

OH + VOL) / (VCC – 2)) – 2

3.3V

125

Ω

125

Ω

84

Ω

84

Ω

Z

o = 50Ω

Z

o = 50Ω

FOUT

FIN

The clock layout topology shown below is a typical termina-

tion for LVPECL outputs. The two different layouts mentioned

are recommended only as guidelines.

FOUT and nFOUT are low impedance follower outputs that gen-

erate ECL/LVPECL compatible outputs. Therefore, terminating

resistors (DC current path to ground) or current sources must

be used for functionality. These outputs are designed to drive

50

Ω transmission lines. Matched impedance techniques should

be used to maximize operating frequency and minimize signal

distortion.

Figures 3A and 3B show two different layouts which

are recommended only as guidelines. Other suitable clock lay-

outs may exist and it would be recommended that the board

designers simulate to guarantee compatibility across all printed

circuit and clock component process variations.

FIGURE 3B. LVPECL OUTPUT TERMINATION

FIGURE 3A. LVPECL OUTPUT TERMINATION

TERMINATION FOR 3.3V LVPECL OUTPUTS

Similar Part No. - ICS8534AY-01T

Manufacturer	Part #	Datasheet	Description
Integrated Device Techn...	ICS8534AY-01T	1Mb / 20P	LOW SKEW, 1-TO-22 DIFFERENTIAL-TO-3.3V LVPECL FANOUT BUFFER

More results

Similar Description - ICS8534AY-01T

Manufacturer	Part #	Datasheet	Description
Renesas Technology Corp	8534-01	707Kb / 22P	Low Skew, 1-to-22 Differential-to-3.3V LVPECL Fanout Buffer December 1, 2015
Integrated Device Techn...	ICS8534-01	1Mb / 20P	LOW SKEW, 1-TO-22 DIFFERENTIAL-TO-3.3V LVPECL FANOUT BUFFER
Texas Instruments	LMK00725	1,006Kb / 23P	[Old version datasheet] Low Skew, 1-to-5, Differential-to-3.3V LVPECL Fanout Buffer
Pericom Semiconductor C...	PI6C485311	370Kb / 6P	3.3V Low Skew 1-to-2 Differential to LVPECL Fanout Buffer
Integrated Device Techn...	8533AG-01LFT	280Kb / 17P	LOW SKEW, 1-TO-4 DIFFERENTIAL-TO-3.3V LVPECL FANOUT BUFFER
Renesas Technology Corp	8533I-01	492Kb / 19P	Low Skew, 1-to-4 Differential-to-3.3V LVPECL Fanout Buffer 7/9/15
Integrated Circuit Syst...	ICS8531-01	145Kb / 13P	LOW SKEW, 1-TO-9 DIFFERENTIAL-TO-3.3V LVPECL FANOUT BUFFER
Pericom Semiconductor C...	PI6C485311WE	370Kb / 6P	3.3V Low Skew 1-to-2 Differential to LVPECL Fanout Buffer
Renesas Technology Corp	8533-01	411Kb / 18P	Low Skew, 1-to-4 Differential-to-3.3V LVPECL Fanout Buffer January 19, 2016
Integrated Circuit Syst...	ICS85304-01	154Kb / 13P	LOW SKEW, 1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL FANOUT BUFFER

More results

ICS8534AY-01T Datasheet(PDF) 8 Page - Integrated Circuit Systems

ICS8534AY-01T Datasheet(HTML) 8 Page - Integrated Circuit Systems

Similar Part No. - ICS8534AY-01T

Similar Description - ICS8534AY-01T

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Datasheet Download

Link URL