2 / 2 page
Notes: All dimensions are typical in inches (mm)
Tolerance x.xx =
±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation on the
side of the unit
Model
Number
Input
Output
Load
Regulation
(%, Max)
Efficiency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
Voltage (VDC)
Current (mA)
Voltage
(VDC)
Current
(mA, Max)
Current
(mA, Min)
Nominal
Range
Full-Load No-Load
D101EI
5
4.5 - 5.5
256
30
5.0
200.0
20.0
15
78
500
D102EI
5
4.5 - 5.5
256
30
9.0
111.0
12.0
15
78
500
D103EI
5
4.5 - 5.5
250
30
12.0
83.0
9.0
15
80
500
D104EI
5
4.5 - 5.5
247
30
15.0
67.0
7.0
15
81
500
D105EI
5
4.5 - 5.5
278
30
±5.0
±100.0
±10.0
15
72
500
D106EI
5
4.5 - 5.5
267
30
±9.0
±56.0
±6.0
15
78
500
D107EI
5
4.5 - 5.5
247
30
±12.0
±42.0
±5.0
15
81
500
D108EI
5
4.5 - 5.5
250
30
±15.0
±33.0
±4.0
15
80
500
D111EI
12
10.8 - 13.2
107
15
5.0
200.0
20.0
15
78
200
D112EI
12
10.8 - 13.2
104
15
9.0
111.0
12.0
15
80
200
D113EI
12
10.8 - 13.2
103
15
12.0
83.0
9.0
15
81
200
D114EI
12
10.8 - 13.2
104
15
15.0
67.0
7.0
15
80
200
D115EI
12
10.8 - 13.2
114
15
±5.0
±100.0
±10.0
15
75
200
D116EI
12
10.8 - 13.2
104
15
±9.0
±56.0
±6.0
15
80
200
D117EI
12
10.8 - 13.2
103
15
±12.0
±42.0
±5.0
15
81
200
D118EI
12
10.8 - 13.2
105
15
±15.0
±33.0
±4.0
15
79
200
D121EI
24
21.6 - 26.4
53
8
5.0
200.0
20.0
15
78
100
D122EI
24
21.6 - 26.4
53
8
9.0
111.0
12.0
15
79
100
D123EI
24
21.6 - 26.4
53
8
12.0
83.0
9.0
15
79
100
D124EI
24
21.6 - 26.4
53
8
15.0
67.0
7.0
15
79
100
D125EI
24
21.6 - 26.4
58
8
±5.0
±100.0
±10.0
15
72
100
D126EI
24
21.6 - 26.4
55
8
±9.0
±56.0
±6.0
15
78
100
D127EI
24
21.6 - 26.4
53
8
±12.0
±42.0
±5.0
15
78
100
D128EI
24
21.6 - 26.4
52
8
±15.0
±33.0
±4.0
15
80
100
Pin
Single
Dual
Pin
Single
Dual
1
+Vin
+Vin
6
No Pin
Common
2
-Vin
-Vin
7
+Vout
+Vout
5
-Vout
-Vout
Derating Curve
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
3. These converters
will operate without
external compo-
nents. However,
when measuring
output ripple, it is
recommended that
an external ceramic
capacitor be placed
from the +Vout pin to the -Vout pin for single output units and from each
output to common for dual output units. An input capacitor will enhace sta-
bility over temperature and input line variations. Recommended capacitor
values are given in the table above. For applications requiring very low
output noise levels, a simple LC filter should be effective.
4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC
output. To do this, connect the load across the positive (+Vout) and nega-
tive (-Vout) outputs and float the output common
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Vin
Input
Capacitor
Vout
Output Capacitor
Single
Dual
5 VDC
4.7
μF
5 VDC 10.0
μF
4.7
μF
12 VDC
2.2
μF
9 VDC
4.7
μF
2.2
μF
24 VDC
1.0
μF 12 VDC
2.2
μF
1.0
μF
15 VDC
1.0
μF 0.47 μF
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
■
TEL: (781) 344-8226
■
FAX: (781) 344-8481
■
E-Mail: sales@micropowerdirect.com
Model Selection Guide
Mechanical Dimensions
Pin Connections