Electronic Components Datasheet Search |
|
69F1608RPFI Datasheet(PDF) 7 Page - Maxwell Technologies |
|
69F1608RPFI Datasheet(HTML) 7 Page - Maxwell Technologies |
7 / 33 page 7 All data sheets are subject to change without notice ©2005 Maxwell Technologies All rights reserved. 128 Megabit (16M x 8-Bit) Flash Memory Module 69F1608 01.07.05 REV 2 NAND FLASH TECHNICAL NOTES Invalid Block(s) Invalid blocks are defined as blocks that contain one or more invalid bits whose reliability is not guaranteed by the manufacturer. Typically, an invalid block will contain a single bad bit. The information regarding the invalid block(s) is called the invalid block information. The invalid block information is written to the 1st or the 2nd page of the invalid block(s) with 00h data. Devices with invalid block(s) have the same quality level as devices with all valid blocks and have the same AC and DC characteristics. An invalid block(s) does not affect the performance of valid block(s) because it is isolated from the bit line and the common source line by a select transistor. The system design must be able to mask out the invalid block(s) via address mapping. The 1st block of the NAND Flash, however, is fully guaran- teed to be a valid block. Identifying Invalid Block(s) All device locations are erased (FFh) prior to shipping. Therefore, the system must be able to create the invalid block table via the following suggested flow chart (Figure 1). CE low to status output t CSTO 9, 10, 11 -- 45 ns RE high to WE low t RHW 9, 10, 11 0 -- ns WE high to RE low t WHR 9, 10, 11 60 -- ns RE access time (read ID) t READID 9, 10, 11 -- 35 ns Device resetting time (read/program/erase) after erase suspend t RST 9, 10, 11 -- 5/10/500 µ s 1. Not Tested 2. If CE goes high within 30 ns after the rising edge of the last RE, R/B will not return to V OL. 3. The time to Ready depends on the value of the pull-up resistor tied to R/B pin. 4. To break the sequential read cycle, CE must be held high for longer than t CEH. TABLE 12. 69F1608 VALID BLOCKS 1,2 1. The device may include invalid blocks. Invalid blocks are defined as blocks that contain one or more bad bits. Do not try to access these invalid blocks for program and erase. During its life time of 10 years and/or 1 million program/erase cycles, the minimum number of valid blocks are guaranteed though its initial number could be reduced. 2. The 1st block, which is placed on the 00h block address, is guaranteed to be a valid block. PARAMETER SYMBOL MIN TYP MAX UNIT Valid Block Number N VB 502 508 512 Blocks TABLE 11. 69F1608 AC CHARACTERISTICS FOR OPERATION (V CC = 5 V ± 10%, TA = -40 TO +125 °C, UNLESS OTHERWISE NOTED) PARAMETER SYMBOL SUBGROUPS MIN MAX UNIT |
Similar Part No. - 69F1608RPFI |
|
Similar Description - 69F1608RPFI |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |