Aluminum Electrolytic Capacitor/TG

Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and / or use.

Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail.

 EE74 

TG

V

Series:

Type :

-40 to +125

°C

10 to 100 V .DC

10 to 4700 µ F

±20 % (120Hz/+20

°C)

I

0.01 CV or 3(µ A) after 2 minutes (whichever, greater)

W.V. (V)

10

16

25

35

50

63

80

100

-25 / +20

°C

3

2

2

2

2

2

2

2

-40 / +20

°C

6

4

4

3

3

3

3

3

(µF)

TG

Surface Mount Type

s Features

Endurance:125

°C 1000 to 2000 h

Miniaturization(40% less than TA Series)

Low ESR(Low temp)

Vibration-proof product is available upon request.(

φ8 )

s Specifications

Category temp. range

Rated W.V. Range

Nominal Cap. Range

Capacitance Tolerance

DC Leakage Current

tan

δ

Characteristics

at Low Temperature

Endurance

Shelf Life

Resistance to

Soldering Heat

s Marking

W.V. code

Negative polarity

marking

Series

identification

Capacitance

Lot number

W.V. code

( ) reference size

s Dimensions in mm (not to scale)

After applying rated working voltage for 1000 hours(

φ8x6.2), 2000 hours(8x10.2 < ) at +125

±2

°C and then being stabilized at +20°C, capacitors shall meet the following limits.

After storage for 1000 hours at +125 ±2

°C with no voltage applied and then being stabilized

at +20

°C, capacitors shall meet the limits specified in Endurance.(With voltage treatment)

Capacitance change

tan

δ

DC leakage current

Capacitance change

tan

δ

DC leakage current

After reflow soldering ( Refer to page 20 for recommendable temperature profile.) and then

being stabilized at +20

°C, capacitor shall meet the following limits.

±10 % of initial measured value

initial specified value

initial specified value

±30 % of initial measured value (code U:±35%)

300 % of initial specified value (code U:350%)

initial specified value

Please see the attached standard products list

(Inpedance ratio at 120Hz)

0.3 max

w

E~G=L±0.3

H~K=L±0.5

A±0.2

Japan

<

=

<

=

<

=

<

=

<

=

Corresponds to use in the car engine room.

The best for an electronically controlled

unit (ECU, ABS etc).

s Application

=

TG

(>

φ12.5)

=

W.V. code

(µF)

Capacitance

Lot number

Series

identification

Negative polarity

marking

(<

φ10)

=

V

10

16

25

35

Code

A

C

E

V

V

50

63

80 100

Code

H

J

K

2A

D

L

I

W

P

K

Size

code

8.0

6.2 8.3

9.5

3.4 0.65 ±0.1

2.2 0.35

8.0 10.2 8.3

10.0

3.4 0.90 ±0.2

3.1 0.70

10.0 10.2 10.3

12.0

3.5 0.90 ±0.2 4.6

0.70

12.5 13.5 13.5 15.0

4.7 0.90 ±0.3 4.4 0.70

16.0 16.5 17.0 19.0

5.5 1.20 ±0.3 6.7

0.70

18.0 16.5 19.0 21.0

6.7 1.20 ±0.3 6.7 0.70

±0.20

E

F

G

H13

J16

K16

-0.20 to +0.15

±0.20

±0.30

±0.30

±0.30

<

=