2322 662 96...

PTC Thermistors For Degaussing,

Dual, Mono And Double Mono Cased

Vishay BCcomponents

Document Number: 29077

For technical questions contact: nlr.europe@vishay.com

www.vishay.com

Revision: 10-Oct-03

185

DUAL RANGE

ELECTRICAL DATA AND ORDERING INFORMATION

MINIMUM

INRUSH CURRENT

(A)

MAXIMUM

RESIDUAL CURRENT

(mA)

(Ω

Ω

Ω

Ω)

(Ω

Ω

Ω

Ω)

TYPICAL DECAY

PERFORMANCE

2322 662 .....

after

5 s

after

30 s

after

180 s

±

±

±

±%

MIN.

TYP.

DECAY

(ms)

ALPHA

(%)

4e/1e pitch

4e/2e pitch

11

50

5

2

30

25

17

25

60

36

−

96209

96309

14

50

5

2

26

25

14

17

40

43

−

96211

96311

16

80

8

4

22

25

14

17

40

44

−

96216

96316

16

80

8

2

22

25

10

17

65

33

LD

96616

96716

20

80

8

2

18

25

10

13

50

38

−

96624

96724

18

80

15

2

18

25

10

17

75

29

LD

96626

96726

25

80

10

4

14

25

10

10

40

45

−

96602

96702

25

80

10

4

14

25

10

10

45

40

LD

96642

96742

21

80

10

5

12

20

10

17

70

36

LT

96606

96706

21

100

20

5

12

20

10

17

80

30

LD/LT

96646

96746

20

100

40

5

9

20

13

20

95

33

LT

96608

96708

20

100

25

10

9

20

13

20

115

26

LD/LT

96648

96748

21

100

40

10

7

20

20

20

110

33

LD/LT

−

96709

19

200

20

10

7

20

5

7

80

31

LT

96213

96313

27

200

50

14

5

30/15

5

6

85

30

−

96605

96705

30

200

20

10

5

20

4

5

85

31

LD/LT

96645

96745

30

200

20

10

3

30/15

4

6

115

29

LD

96643

96743

MONO CASED RANGE

ELECTRICAL DATA AND ORDERING INFORMATION

Notes

1. Electrical data and catalog numbers. The shading indicates preferred types.

2.

All peak-to-peak currents are measured at typical resistance of the coil, at 50 Hz (AC), at 25ºC and at 220 Vrms for the 276V types, and 110Vrms for the 145V types.

3. Lower tolerances on resistance of degaussing PTC are available on request.

4. Lower minimum coil resistance is available on request.

5. Decay time is the time from the moment of maximum peak current until the half of the maximum peak inrush current.

6. Alpha maximum is the maximum decrease in current expressed in percent between two successive peaks.

7. Inrush currents and decay times at other voltage coil combinations can be derived from Figures 7 to 13, see section

‘Introduction, PTC thermistors for degaussing”.

8. LT = low tolerance; LD = long decay.

9. Smallest packaging quantity (SPQ) = 600 units.

MINIMUM

INRUSH

CURRENT

(A)

MAXIMUM

RESIDUAL CURRENT

(mA)

(Ω

Ω

Ω

Ω)

(Ω

Ω

Ω

Ω)

TYPICAL DECAY

PERFORMANCE

2322 662 .....

after

5 s

after

30 s

after

180 s

±

±

±

±%

MIN.

TYP.

DECAY

ALPHA

4e pitch

11

100

40

20

30

25

17

25

75

30

−

96281

12

50

30

20

26

25

14

25

90

30

−

96688

16

80

40

20

22

25

14

17

40

44

−

96286

20

100

50

25

18

25

10

13

50

38

−

96682

25

200

50

30

14

25

10

10

40

45

−

96683

25

200

80

30

14

25

10

10

45

40

LD

96692

21

200

80

30

12

20

10

17

70

36

−

96684

21

200

80

30

12

20

10

17

80

30

LD

96696

20

100

50

30

9

20

13

20

95

33

LT

96687

20

200

50

25

9

20

13

20

115

26

LD/LT

96698

21

100

50

30

7

20

20

20

110

33

LD/LT

96681

19

200

70

40

7

20

5

7

80

31

−

96285

27

200

70

40

5

30/1

5

6

85

30

−

96686

30

200

70

40

5

20

4

5

85

31

LD

96695

30

200

70

40

3

30/1

4

6

115

29

LD

96693