Electronic Components Datasheet Search |
|
LTC4006EGN-4 Datasheet(PDF) 8 Page - Linear Technology |
|
LTC4006EGN-4 Datasheet(HTML) 8 Page - Linear Technology |
8 / 16 page 8 LTC4006 sn4006 4006is therefore, I V R A k R CHARGE REF IMON SENSE =µ Ω –. • 11 67 3 The voltage at BAT is divided down by an internal resistor divider and is used by error amp EA to decrease ITH if the divider voltage is above the 1.19V reference. When the charging current begins to decrease, the voltage at IMON will decrease in direct proportion. The voltage at IMON is then given by: VI R A k R k IMON CHARGE SENSE IMON =+ µ Ω () Ω •. • • 11 67 3 3 VIMON is plotted in Figure 2. The amplifier CL1 monitors and limits the input current to a preset level (100mV/RCL). At input current limit, CL1 will decrease the ITH voltage, thereby reducing charging cur- rent. When this condition is detected, the C/10 indicator OPERATIO will be inhibited if it is not already active. If the charging current decreases below 10% to 15% of programmed current, while engaged in input current limiting, BGATE will be forced low to prevent the charger from discharging the battery. Audible noise can occur in this mode of operation. An overvoltage comparator guards against voltage tran- sient overshoots (>7% of programmed value). In this case, both MOSFETs are turned off until the overvoltage condition is cleared. This feature is useful for batteries which “load dump” themselves by opening their protec- tion switch to perform functions such as calibration or pulse mode charging. As the voltage at BAT increases to near the input voltage at DCIN, the converter will attempt to turn on the top MOSFET continuously (“dropout’’). A watchdog timer detects this condition and forces the top MOSFET to turn Table 1. Truth Table for LTC4006 Operation MODE DCIN BAT VOLTAGE BAT CURRENT ACP/SHDN TIMER STATE CHG* Shut Down by Low Adapter Voltage <BAT >UVLO Leakage LOW Reset HIGH Conditioning a Depleted Battery >BAT <2.5V/Cell 10% Programmed HIGH Running LOW Current Normal Charging >BAT >2.5V/Cell Programmed HIGH Running LOW Current Input Current Limited Charging >BAT >2.5V/Cell Unknown HIGH Running LOW Charger Paused Due to Thermistor Out of Range >BAT X OFF HIGH Paused LOW (Faulted) Shut Down by ACP/SHDN Pin >BAT X OFF Forced LOW Reset HIGH Terminated by Low-Battery Fault (Note 1) >BAT <2.5V/Cell OFF HIGH >T/4 Stopped HIGH (Faulted) Top-Off Charging. C/10 is Latched >BAT VFLOAT OFF HIGH <T/4 After C/10 25 µA Comparator Trip. Running Timer is Reset by C/10 Comparator (Latched), >BAT VFLOAT OFF HIGH >T/4 After C/10 HIGH then Terminates After 1/4 T Comparator Trip. (Waiting Stopped for Restart) Terminated by Expired Timer >BAT VFLOAT** OFF HIGH >T Stopped HIGH (Waiting for Restart) Timer Defeated. (Low-Battery Conditioning Still X X X X X Forced LOW Functional) Shut Down by Undervoltage Lockout >BAT <UVL OFF HIGH Reset HIGH** and <UVL Timer Defeated Until VBAT > 3.9V/Cell >BAT 2.5V ≤ VBAT ≤3.9V Programmed HIGH Running LOW (V/Cell) Current *Open Drain. High when used with pull-up resistor. **Most probable condition, X = Don’t care Note 1: If a depleted battery is inserted while the charger is in this state, the charger must be reset to initiate charging. |
Similar Part No. - LTC4006EGN-4 |
|
Similar Description - LTC4006EGN-4 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |