COMLINK™ SERIES
CY2CC1910
Document #: 38-07347 Rev. *B
Page 2 of 8
Maximum Ratings[1,2]
Storage Temperature: ................................–65
°C to + 150°C
Ambient Temperature:................................... –40
°C to +85°C
Supply Voltage to Ground Potential
VCC .................................................................. –0.5V to 4.6V
Input ................................................................. –0.5V to 5.8V
Supply Voltage to Ground Potential
(Outputs only) ........................................... –0.5V to VDD + 1V
DC Output Voltage.................................... –0.5V to VDD + 1V
Power Dissipation........................................................ 0.75W
Variable Output Impedance Control (VOI™)
DC Electrical Characteristics @ 3.3V (see Figure 2)
Parameter
Description
Conditions
Min.
Typ.
Max.
Unit
VOH
Output High Voltage
VDD = Min.,VIN = VIH or VIL
IOH = –12 mA
2.3
3.3
V
VOL
Output Low Voltage
VDD = Min.,VIN = VIH or VIL
IOL = 12 mA
0.2
0.5
V
V
IH
Input High Voltage
Guaranteed Logic High Level
2
5.8
V
V
IL
Input Low Voltage
Guaranteed Logic Low Level
0.8
V
I
IH
Input High Current
VDD = Max.
VIN = 2.7V
1
uA
IIL
Input Low Current
VDD = Max.
VIN = 0.5V
–1uA
II
Input High Current
VDD = Max.,VIN = VDD(Max.)
20
uA
V
IK
Clamp Diode Voltage
VDD = Min., IIN = –18 mA
–0.7
–1.2
V
I
OK
Continuous Clamp Current
VDD = Max.,VOUT = GND
–50
mA
O
OFF
Power-down Disable
VDD = GND,VOUT = < 4.5V
100
uA
V
H
Input Hysteresis
80
mV
DC Electrical Characteristics @ 2.5V (see Figure 2)
Parameter
Description
Conditions
Min.
Typ.
Max.
Unit
V
OH
Output High Voltage
VDD = Min.,VIN = VIH or VIL
IOH = –7 mA
1.8
V
VDD = Min.,VIN = VIH or VIL
IOH = 12 mA
1.6
V
V
OL
Output Low Voltage
Guaranteed Logic High Level
IOL = 12 mA
0.65
V
V
IH
Input High Voltage
Guaranteed Logic Low Level
1.6
5.0
V
V
IL
Input Low Voltage
VDD = Max.
0.8
V
I
IH
Input High Current
VDD = Max.
VIN = 2.4V
1
uA
I
IL
Input Low Current
VDD = Max.,VIN = VDD(Max.)
VIN = 0.5V
–1uA
I
I
Input High Current
VDD = Min., IIN = –18 mA
20
uA
V
IK
Clamp Diode Voltage
VDD = Max.,VOUT = GND
–0.7
–1.2
V
I
OK
Continuous Clamp Current
VDD = GND, VOUT = < 4.5V
–50
mA
O
OFF
Power-down Disable
VDD = Min.,VIN = VIH or VIL
100
uA
V
H
Input Hysteresis
80
mV
Note:
1.
Multiple Supplies: The Voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required.
2.
Stresses greater than those listed under absolute maximum ratings may cause permanent damage to the device. This is intended to be a stress rating only
and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Pull Down
0
0.5
1
1.5
2
2.5
3
3.5
0
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.08
0.09
0.1
Iol (A)
Vdd = 3.3 V
Vdd = 2.5 V
Vdd = 1.8 V
Pull Up
0
0.5
1
1.5
2
2.5
3
3.5
-0.18
-0.16
-0.14
-0.12
-0.1
-0.08
-0.06
-0.04
-0.02
0
Ioh (A)
Vdd= 3.3 V
Vdd= 2.5 V
Vdd= 1.8 V
Figure 1. Output Voltage vs. Output Current (TA = 25°C)